Certifi cations may vary depending on country of origin. Notes: 1 Computed on cubic volume of bin. Does not refl ect voids that can occur due to pyramiding. 2 Dispense assembly removes if necessary for installation access through 915mm (36") door opening. © Follett Corporation Form #2975 10/07 Ice Pro™ automatic ice bagging and dispensing system Patent #6,685,053/6,860,408 Patente No.6,685,053/6,860,408 Brevet No.6,685,053/6,860,408 Patent Nr.6,685,053/6,860,408 Follett recommends installation o

Grasp the end of the front window and pull toward you as the window is slid to the opposite side. Repeat for rear window. rear window front window 2. Wash bin walls, hopper, access door plate and partition (if any), rinse and sanitize. Exterior bin care Exterior stainless steel surfaces can be cleaned with a stainless steel cleaner such as 3M Stainless Steel Cleaner & Polish or equivalent. Technical assistance available toll free Should you have any questions concerning installation or ma

To ensure that your equipment delivers this same degree of service, please read this manual carefully before installing or operating the system. If you have questions during installation or operation of this system, please call our technical service group at (800) 523-9361 or (610) 252-7301. Before you begin After uncrating, remove all packing material and inspect equipment for shipping damage. If damage is found, notify shipper immediately and contact Follett so that we can help in filing a c

use non-chlorine based cleaner and sanitizer suitable for use in a food zone. Do Not use chlorine-based cleaners, which can cause staining and pitting of stainless steel components. Do not run Totes through a dishwasher. Turn off icemaker(s) and remove ice from bin before beginning. Bin drain system cleaning 1. Remove upper tray(s) and wash with cleaning solution, rinse and reposition in brackets. 2. Saturate a cloth with cleaning solution and insert through a loop in end of a piece of wire.

This often happens if ice has been held in storage for a period of time without use. Use supplied paddle accessory to break up bridges (see caution below): 1. Completely knock down all ice from sides and back of bin. 2. Knock down any bridge that has occurred in middle. 3. Agitate paddle back and forth to break up congealed ice mass. A Do Not dig up at ice. Instead, break away “legs” that are holding bridges. Ice above will then fall. To avoid injury, do not attempt to break up bridged ic

A36000 luaTHMaT« M£T«^opàç Kai Ano0nK£uanç nóyou SmartGATE EyxelPÍSlo Xpnapç Apië^ôç Met6 Tpv E^unnpETpop: A36000 Contenitori SmartGATE per la conservazione e carrelli per il transporto del ghiaccio Manuale di funzionamento per i modelli successivi al no. A36000 Sistemas de armazenamento e de transporte de gelo com o dispositivo SmartGATE Manual de utilizaçâo para modelos a partir de A36000 Iskubsförvaring och transportsystem med SmartGATE Drift- och skötselhandbok Fr. o. m. modell A3600

SMARTGATE can be raised and locked in higher position for better flow or when more access is needed. 5 Cleaning A Clean and sanitize bin and cart(s) interiors prior to use and on regular schedule as needed. use non-chlorine based cleaner and sanitizer suitable for use in a food zone. Do Not use chlorine-based cleaners, which can cause staining and pitting of stainless steel components. Do not run Totes through a dishwasher. Turn off icemaker(s) and remove ice from bin before beginning. Bin

Para asegurarse de que su equipo ofrezca el mismo nivel de servicio, lea detenidamente este manual antes de instalar o poner en funcionamiento el sistema. Si tiene cualquier pregunta durante la instalación o funcionamiento de este sistema, llame a nuestro equipo de servicio técnico al (610) 252-7301. A Precauciones importantes y normas de funcionamiento Lea detenidamente todo el manual antes de montar o accionar el Sistema de transporte de hielo y siga las precauciones e instrucciones indicadas

13. Remove icemaker top panel and Fig. 8 louvered side panel. 14. Insert ice transport tube to a 1/2" (13mm) depth through mounting bracket (Fig 8 and 9.1) and secure transport tube away from condenser fan under float reservoir bracket (Fig. 9.2). 15. Tighten clamp screw(s) on icemaker base securely (Fig. 9.3). 16. Uncoil capillary tube from bin thermostat and route through hole in gasket to mounting bracket and secure as shown (Fig. 8). 17. Reinstall icemaker louvered side panel and top panel.

BLACK RED HIGH PRESSURE SAFETY SWITCH 4 2 3 RUNSTART T.O.L. BLUE YELLOWBLACK WHITE M blk wire is on 24V) 22 Normal operation – Stage 4 Once the ice level control opens, the B-E LED goes out. After a 10 second delay the LED (C), compressor, and fan motor go off and the B-T LED comes on. (Should the ice level control not remain open for 10 seconds, the icemaker will continue to run.) The gearmotor continues to run for 60 seconds. The purpose of this function is to drive the remaining ice out of th