All notices are to be kept in good condition. Replace any unreadable or damaged labels. Site preparation The dispenser must have at least four inches of space behind it. This space is needed for airflow, air filter removal, and cleaning. Minimal clearance is required between the dispenser sides and the wall or another appliance. The dispenser performs better if not placed near any heating appliance. Leave some space so the dispenser can be moved for cleaning. 41084 102709 INTRODUCTION Safety fir

The indication must be: a) 120 volts ac for two wire 120 volt models. b) 240 volts ac for two wire 240 volt models. c) 100 volts ac for two wire 100 volt models. 8. Disconnect the brewer from the power source. If voltage is present as described, reinstall the capillary tube into the tank to the line 4.5" above the bulb, the control thermostat is operating properly. If voltage is not present as described, replace the thermostat. Removal and Replacement: 1. Remove both wires from the control therm

6. Place the ON/OFF or SELECTOR switch in the “ON” position. 7. Momentarily press the start switch. CAUTION -The funnel contains hot liquids. Remove funnel slowly. 8. Carefully remove the brew funnel and discard the used filter when tea no longer drips from the funnel tip. 9. Place the ON/OFF or SELECTOR switch in the "OFF" position to prevent a false start. 10. Fresh tea is available at the faucet. 10145 072600 Page 7 TROUBLESHOOTING A troubleshooting guide is provided to suggest probable cause

If the sound is not heard as described, replace the solenoid valve. Removal and Replacement: 1. Remove all wires from solenoid valves. 2. Turn off the water supply to the brewer. 3. Disconnect the water lines to and from the solenoid valves. 4. Remove the two #8-32 keps nuts holding the mounting bracket to the brewer base. 5. Lift out the bracket. 6. Remove the two #10-32 slotted-head screws holding the solenoid valve to the mounting bracket. 7. Securely install the new solenoid valve to the mou

2. Remove circuit board and spacers (as required). 3. Remove all wires from the timer. 4. Attach all wires to the replacement timer board prior to installation to the component mounting bracket. Refer to FIG. 7 when reconnecting the wires. 5. Install new circuit board with spacers (as required) to the component mounting bracket. 6. Adjust the timer as described below. Timer Setting: NOTE: Prior to setting or modifying volumes, check that the brewer is connected to water supply, the tank is prope

TU3 HOT L I Q U I D ! CAUTION OPERATING & SERVICE MANUAL BUNN-O-MATIC CORPORATION POST OFFICE BOX 3227 SPRINGFIELD, ILLINOIS 62708-3227 PHONE: (217) 529-6601 FAX: (217) 529-6644 10225.0000N 03/04 ©1987 Bunn-O-Matic Corporation CONTENTS Introduction .....................................................................2 Warranty ..........................................................................2 User Notices ....................................................................3 Electrical &

6. Carefully bend the capillary tube so that the tube and bulb inside the tank are in a vertical position. NOTE: The capillary tube must be clear of any electrical termination and not kinked. 7. Fasten the new control thermostat to its bracket. 8. Refer to Fig. 7 when reconnecting the wires. 9. Adjust the control thermostat as required. BUNNOFF BLK to Tank Heater (100/120V) Thermal Fuse (230V) BLU/BLK to Limit Thermostat P2090.80 FIG. 7 CONTROL THERMOSTAT TERMINALS 37236 080504 Page 19 SERVICE (

Test Procedures: 1. Disconnect the brewer from the power source. 2. Disconnect the white/violet and white/green wires from the solenoid valve. With the ON/OFF switch in the "ON" position ("UNSWEET" or "SWEET" position for brewers with sweetener option), press the start switch. 3. With a voltmeter, check the voltage across the white/violet and white/green wires. Connect the brewer to the power source. The indication must be: a) 120 volts ac for two wire 120 volt models. b) 230 volts ac for two wi

SplashGard® funnel and funnel locks help improve safety. Funnel has 28 ounce (.8 kg) ground coffee capacity and paper filter retainers to eliminate fold-over. Titan TF servers are insulated to keep coffee hot for hours. Hot water faucet. Energy-saver mode reduces tank temperature during idle periods. Model Titan Dual Brewer with 3 gallon TF Servers (servers sold separately) Dimensions: 40.02” H x 35.63” W x 21.74” D (101.7cm Hx 90.5cm Wx 55.2cm D) For current specification sheets and othe

5-year parts and 1-year labor warranty on compressor and 3-year parts and labor warranty on electronics. See the product manual for additional details. • Sanitation listed by NSF to Standard 6 and 18 (including dairy & alcohol) and safety listed by ETL to UL Standard (UL 471) and csA Standard (c22.2 No. 120). • White/Stainless, Black,Stainless and all Black finishes available. • International electrical configurations available. Ultra-1 Dimensions: 31.9”H x 7.9”W x 24.2”D (81 cm H x 20.1 c