Si tiene dudas o comentarios, contactenos. 1-877-FNA-GAS1 (1-877-362-4271)•InstructIon ManuaL INSTRUCTIVO DE OPERACION, CENTROS DE SERVICIO Y POLIZA GuIDe D'utILIsatIon DE GARANTIA. aDVertencIa: LEASE ESTE INSTRUCTIVO ANTES DE USAR EL PRODUCTO. ManuaL De InstruccIones DH3028 Pressure Washer Laveuse a pression Lavadora a presion 2 English A. Panel assembly B. Nozzle grommets C. Professional spray gun D. Wheel E. Quick-connect spray wand F. Frame G. Engine dipstick/oil plug H. Engine switch I. Sta

Si tiene dudas o comentarios, contactenos. InstructIon ManuaL GuIDe D'utILIsatIon ManuaL De InstruccIones INSTRUCTIVO DE OPERACION, CENTROS DE SERVICIO Y POLIZA DE GARANTIA.aDVertencIa: LEASE ESTE INSTRUCTIVO ANTES DE USAR EL PRODUCTO. 1-800-4-DeWALT • DP2800 Pressure Washer Laveuse a pression Lavadora a presion English Specifications MODEL WEIGHT HEIGHT WIDTH Length PSI Max* Op erating PSI GPM Max* Op erating GPM Engi ne DP2800 97 lbs 26.5" 23" 40" 2800 2520 3.0 2.7 Honda 6.5 Hp GX200 * Water f

POSSIBLE SOLUTION Add fuel. 2 Low oil. Add required amount of oil. 3 Pressure builds up after two pulls on the recoil starter or after initial use. Squeeze gun trigger to relieve pres sure. 4 Choke lever in the NO CHOKE position. Move choke to the CHOKE po si tion. 5 Spark plug wire not attached. Attach spark plug wire. 6 Engine ON/OFF switch in OFF po si tion. Place engine ON/OFF switch in ON position. 7 Choke lever in the CHOKE position on a hot engine or an engine that has been exposed to the

HoW to PreVent It • Shut off engine and allow it to cool before adding fuel to the tank. • Use care in filling tank to avoid spilling fuel. Move pressure washer away from fueling area before starting engine. • Keep maximum fuel level 1/2" (12.7 mm) below bottom of filler neck to allow for expansion. • Operate and fuel equipment in well-ventilated areas free from obstructions. Equip areas with fire extinguisher suitable for gasoline fires. 4 • Materials placed against or near the pressure washer

The thermal relief valve will then close. If pump is left in bypass mode for more than two minutes internal components of the pump can be damaged. Start-up Procedure 1. In a well-ventilated outdoor area, add fresh, high-quality, unleaded gasoline with a pump octane rating of 86 or higher. Do not overfill. Wipe up spilled fuel before starting the engine. Refer to engine instruction manual for correct procedure. 2 . Check engine oil level. Refer to the engine instruction manual for correct procedu

• Improperly stored fuel could lead to acciden tal ignition. Fuel im prop erly secured could get into the hands of children or oth er un qual i fied persons. • Use of acids, toxic or cor ro sive chemicals, poisons, in sec ti cides, or any kind of flam ma ble solvent with this product could re sult in se rious injury or death. live plants) that could be damaged from muffler exhaust heat. • Store fuel in an OSHAap proved con tain er, in a se cure location away from work area. • Do not spray flamma

If the nozzle becomes partially clogged or restricted, the pump pressure will pulsate. Clean the nozzle immediately using the nozzle kit supplied and the following instructions: 1. Shut off the pressure washer and turn off the water supply. 2. Pull trigger on gun handle to relieve any water pressure. 3. Disconnect the spray wand from the gun. 4. Remove the high-pressure nozzle from the spray wand. Remove any obstructions with the nozzle cleaning tool (BB) provided and back flush with clean water

1) 1. Place handle assembly (O) onto frame, depress the snap buttons, and slide the handle assembly onto the frame (F) until snap buttons are secured in place. CAUTION: Risk of personal injury. Avoid placing hands between handle and frame when assembling to prevent pinching. F O note: The high-pressure pump was filled with oil at the factory. Always check oil level before using (refer to Maintenance for more information). WARNING: Risk of bursting. Use a tire pressure gauge to check the tires pr

To remove Tires 1. Using a 1/8" hex head wrench loosen set screw in hub collar. 2. Slide hub collar from axle and remove the tire. STorAGE Engine U Consult the engine instruction manual for the manufacturer's recommendations for storage. Pump The manufacturer recommends using a pump protector/winterizer, such as DeWALT winterizer (DP80) when storing the unit for more than 30 days and/or when freezing temperatures are expected. DeWALT winterizer (DP80) is availabe at the store where the pressure

Engine dipstick/oil plug - Jauge graduée/Bouchon du réservoir d’huile du moteur - Tapón/varilla para medición del nivel de aceite del motor J. High-pressure pump - Pompe haute pression - Bomba de alta presión K. Engine - Moteur - Motor L. Choke control - Commande d’étrangleur - Control de la estrangulación del carburador M. Starter grip - Poignée de démarrage - Agarradera de arranque N. Fuel valve lever - Levier de la soupape à essence - Palanca de la válvula de combustible O. Engine switch