63 Istruzioni sull'uso .................................... 83 Driftsinstruks........................................... 103 Bruksanvisning ....................................... 123 Driftsvejledning ....................................... 143 Kayttoohje .............................................. 163 Navodilo za uporabo............................... 183 Uputstvo za rad....................................... 203 Prevadzkovy navod ................................ 223 Provozni navod .........

Если Ваши моечная машина высокого давления или принадлежности сдаются в ремонт, должна прилагаться копия чека. Гарантийный ремонт осуществляется в следующих условиях: • дефекты связаны с браком или неисправностями материалов или изделия. (данная гарантия не распространяется износ и неправильное использование); • указания в данном руководстве полностью соблюдались; никто, кроме подготовленных Nilfisk-ALTO специалистов по техническому обслуживанию, не производил и не пытался произвести ремонт; •

A B Poseidon 2 4.5 Start and stop of the machine (when connected to a water supply) 4.6 Start the machine (when connected to open containers (suction mode)) 4.7 Pressure regulation on the Flexopower Plus- spray lance The spray lance is affected by a thrust during operation - therefore always hold it firmly with both hands. IMPORTANT: Point the nozzle at the ground. 1. Check that the machine is in upright position. NOTE: Do not place the machine in tall grass! 2. Release the trigger lock. 3. Acti

• Unplug any electrically operated product before attempting to clean it. Direct spray away from electric outlets and switches. • Your washer operates at fluid pressures and velocities high enough to penetrate human and animal flesh, which could result in amputation or other serious injury. Leaks caused by loose fittings or worn or damaged hoses can result in injection injuries. DO NOT TREAT FLUID INJECTION AS A SIMPLE CUT! See a physician immediately! • Relieve system pressure before attempting

1. Obtain a funnel, six ounces of *RV antifreeze, and approximately 12 inches of garden hose with a male hose connector attached to one end. Use only RV antifreeze. Any other antifreeze is corrosive and can damage pump. 2. Disconnect spark plug wire. 3. Disconnect high pressure hose from pump and from spray gun. 4. Connect 12 inch length of hose to water inlet of pump. 5. Add *RV antifreeze to hose as shown. 6. Pull engine starter rope slowly several times until antifreeze comes out of high pres

This valve will then release a gush of water in an effort to lower the temperature inside the pump. Immediately after this occurs, the valve will close. Chemical Injection System: Mixes cleaners or cleaning solvents with the pressurized water to improve cleaning effectiveness. Water Supply: All pressure washers must have a source of water. The minimum requirements for a water supply are 20 PSI and 5 gallons per minute. PRESSURE WASHER OPERATING FEATURES PRESSURE ADJUSTMENTS The pressure setting

Black Green Nozzle Color Red Yellow White Spray Pattern 25. 40. low pressure 0. 15. intense cleaning of small areas intense cleaning of larger areas covers wide areas of cleaning applies cleaning solutions Uses powerful pinpoint for very intense cleaning metal, concrete, wood, or vinyl metal, concrete, or wood metal, concrete, or wood Surfaces * Metal or concrete DO NOT use on wood metal, concrete, wood, or vinyl The high pressure spray from your pressure washer is capable of causing damage to s

You should never run this pressure washer for more than 2 minutes without pulling the trigger to allow cool water to enter the pump and the heated (recirculated) water to exit. ASSEMBLY 1. Place handle assembly onto frame and connect handle to frame. 2. Connect wand to gun. Tighten securely. 3. Attach high pressure hose to gun. Tighten securely. 5. Assemble grommet kit and quick-connect nozzles as described in instructions supplied. 6. Add engine oil (supplied) to engine. Refer to engine manual