4. Flush wand assembly backwards with water or compressed air. 5. If pressure is still too high, repeat steps 2-4. 4. CHECKING OIL: The pump is shipped with the correct amount of oil in it. This pump should never need any oil added or changed unless it develops a leak. A 30 weight non- detergent oil can be used in this pump (approximately 6 oz.). If pump is leaking oil take to an Authorized Service Center. HIGH PRESSURE HOSE: Damaged high pressure hoses can burst which can cause a potentially ha

NOTE: The pressure of the spray on the surface you are cleaning increases as you move the wand closer to the surface. To increase angle to a fan spray, turn counterclockwise To decrease angle to pencil point spray, turn clockwise 4.4 HIGH PRESSURE/TURBO SPRAY Do not move the nozzle to adjust pressure. The high pressure rotary nozzle position is intended for maximum cleaning effect. Keep the spray lance min. 6” to 8” away from the cleaning surface at all times. Rotary Spray USE OF CLEANING CHEMIC

A SMALL AMOUNT OF OIL LEAKAGE IS NORMAL. 5.4 WATER SCREEN The pressure washer is equipped with a water inlet screen to protect the pump. If the screen is not kept clean, the flow of water to the pressure washer will be restricted and the pump may be damaged. • To clean inner water screen, remove quick connect and remove the filter screen from the pump inlet. (see page 4, item 13) • Backflush screen to clean • Replace screen and quick connect immediately to prevent any foreign matter from enterin

This device provides additional protection from the risk of electrical shock. (Figure 1) FLOW RATE: This is the amount of water that passes through your wand. (Usually measured in G.P.M., gallons per minute.). IDLE MODE: This pertains to the time that the pressure washer is running without the trigger on the wand engaged to spray. You should never run this pressure washer for more than 5 minutes without pulling the trigger to relieve pressure. Running the pressure washer in this manner would voi

Operating unit with water supply shut off (without flow of water) will result in equipment damage. During shut-down, entire system including pump, hose and wand will remain under pressure. Do not attempt to remove hose/gun until pressure is relieved. 7 MAINTENANCE AND STORAGE TO AVOID ELECTRICAL SHOCK, ALWAYS DISCONNECT THE PLUG FROM THE ELECTRICAL SUPPLY BEFORE ANY MAINTENANCE IS STARTED. MAINTENANCE 1. WATER SCREEN: Inspect the water screen before attaching water supply. Clean water screen if

NEVER run engine indoors or in enclosed, poorly ventilated areas. Engine exhaust contains carbon monoxide, an odorless and deadly gas. NEVER carry pressure washer with engine running, turn engine off and allow it to cool before carrying pressure washer. DO NOT let hoses come in contact with hot engine muffler during or immediately after use of your pressure washer. Damage to hoses from contact with hot engine surfaces will NOT be covered by warranty. NEVER pull water supply hose to move pressure

. . . . . .2 Important Safety Instructions. . . . .2–5 Specifications ...................6 CartonContents .................6 Assembly Instructions. . . . . . . . . . .6–7 Operating Instructions . . . . . . . . .8–13 Maintenance ................14–15 Storage ....................15–16 Troubleshooting Guide . . . . . . . .17–18 RepairWarranty ................20 IMPORTANT Please make certain that the person who is to use this equipment carefully reads and understands these instructions before operat

Always place pressure washer on a protective mat when transporting to protect against damage to vehicle from leaks. Remove pressure washer from vehicle immediately upon arrival at your destination. A12495 4- ENG RISK OF UNSAFE OPERATION HAZARD WHAT CAN HAPPEN HOW TO PREVENT IT • Reactive force of spray will cause gun/ wand to kickback, and could cause the operator to slip or fall, or misdirect the spray. Improper control of gun/wand can result in injuries to self and others. • If proper starting

1. In a well ventilated outdoor area add fresh, high quality, unleaded gasoline with a pump octane rating of 86 or higher. Do not overfill. Wipe up spilled fuel before starting the engine. Refer to Engine Owners Manual for correct procedure. 2. Check engine oil level. See Engine Owners Manual for correct procedure. NOTE: There will be a slight amount of oil in the engine from factory testing. 3. Verify the filter screen is in water inlet of pump. NOTE: Cone side faces out. Filter Screen 4. Conne