Оценок - 3, средний балл: 3.3
(
)
)
|
Фрагмент инструкции
1) 1. Place handle assembly (O) onto frame, depress the snap buttons, and slide the handle assembly onto the frame (F) until snap buttons are secured in place. CAUTION: Risk of personal injury. Avoid placing hands between handle and frame when assembling to prevent pinching. F O note: The high-pressure pump was filled with oil at the factory. Always check oil level before using (refer to Maintenance for more information). WARNING: Risk of bursting. Use a tire pressure gauge to check the tires pressure before each use and while inflating tires; see the tire sidewall for the correct tire pressure. note: Air tanks, compressors and similar equipment used to inflate tires can fill small tires similar to these very rapidly. Adjust pressure regulator on air supply to no more than the rating of the tire pressure. Add air in small increments and frequently use the tire gauge to 2. Attach high-pressure hose (P) to spray gun. Make sure it is secure. 3. Connect wand (E) to spray gun. Make sure connection is secure. E P prevent over inflation. oPErATIon Pressure Adjustments The pressure setting is preset at the factory to achieve optimum pressure and cleaning. To lower the pressure, follow these instructions. 1. Back away from the surface to be cleaned. The further away you D 4. Thread the side handle (D) into spray gun extension and tighten to desired position. 5. Place the nozzle holder (B) onto the panel assembly (A) and push each nozzle holder into place. 6. Removethefivecoloredquick-connect nozzles from the plastic bag and insert them into correct grommet on the nozzle holder. Nozzles are color coded to match colored nozzles on panel assembly. B A are, the less the pressure will be on the surface to be cleaned. 2. Change to the 40. nozzle (white). This nozzle delivers a less powerful stream of water and a wider spray pattern. Refer to spray Wand nozzles. CAUTION: DO NOT attempt to increase pump pressure. A higher pressure setting than the factory set pressure may damage pump. 3. Reduce the speed of the gasoline engine (RPM). Slow the engine down and the water pressure will go down with it. Spray Wand nozzles (Fig. 1) The nozzles for the spray wand are stored in the nozzle holder (B) on the panel assembly (A). Colors on the panel identify nozzle location and spray pattern. Refer to the following chart to choose the correct nozzle for the job to be performed. 10 nozzle Color spray Pattern uses surfaces* red 0. powerful pinpoint for very intense cleaning metal or concrete; DO NOT use on wood yellow 15. intense cleaning of small areas metal, concrete or wood Green 25. intense cleaning of larger areas metal, concrete or wood White 40. covers wide areas of cleaning metal, concrete, wood or vinyl Black low pressure applies cleaning solutions metal, concrete, wood or vinyl * CAUTION: The high-pressure spray from your pressure washer is capable of causing damage to surfaces such as wood, glass, automobile paint, auto striping and trim, delicate objects such as flowers and shrubs. Before spraying, check the item to be cleaned to assure yourself that it is strong enough to resist damage from the force of spray. ChanGInG nozzLes on sPray WanD DANGER: Risk of fluid injection. Do not direct discharge stream toward persons, unprotected skin, eyes or any pets or animals. Serious injury will occur. WARNING: Flying objects could cause risk of serious injury. DO NOT attempt to change nozzles while pressure washer is running. Turn engine off before changing nozzles. 1. Pull quick-connect coupler back and insert nozzle. 2. Release quick-connect coupler and twist nozzle to make sure it is secure in coupler. WARNING: Flying object could cause risk of serious injury. Ensure nozzle is completely inserted in quick-connect socket and quick- connect snap ring is fully engaged (forward) before squeezing gun trigger. chemicals and cleaning Solvents Applying chemicals or cleaning solvents is a low-pressure operation. note: Use only soaps and chemicals designed for pressure washer use. Do not use bleach. to aPPLy CheMICaLs anD soLVents 1. Press chemical hose (S) onto barbed fitting located near high pressure hose connection of pump as shown. 2. Place the other end of chemical hose with filter on it into the container holding chemical/ cleaning solution. note: For every 7 gallons (26.5 liters) of water pumped 1 gallon (3.8 liters) of chemical/ cleaning solution will be used. S English 11 EnglishEnglish 3. Install low-pressure (black) nozzle into quick connect fitting of spray wand, refer to spray Wand nozzles. note: Chemicals and soaps will not siphon if the black soap nozzle is not installed on the spray wand. 4. After use of chemicals, place chemical hose into container of clean water and draw clean water through chemical injection system to rinse system thoroughly. If chemicals remain in the pump it could be damaged. Pumps damaged due to chemicals will not be covered under warranty. Starting WARNING: To reduce the risk of injury, read the press...
Эта инструкция также подходит к моделям:Моечное оборудование - N0003431 (4.79 mb)