When there is a steady stream of water present, turn water source off. Reconnect water source to pump inlet and turn on water source. Squeeze trigger to remove remaining air. 8. Move choke to the "No Choke" position. 9. Move throttle control lever to the "Fast" position. 10. Use high pressure hose under 100 feet. Will not draw chemicals 7. Chemical build up in chemical injector. 1. Wand not in low pressure. 2. Chemical filter clogged. 3. Chemical screen not in chemical 4. Chemical adjustment kno

1. Obtain a funnel, six ounces of *RV antifreeze, and approximately 12 inches of garden hose with a male hose connector attached to one end. Use only RV antifreeze. Any other antifreeze is corrosive and can damage pump. 2. Disconnect spark plug wire. 3. Disconnect high pressure hose from pump and from spray gun. 4. Connect 12 inch length of hose to water inlet of pump. 5. Add *RV antifreeze to hose as shown. 6. Pull engine starter rope slowly several times until antifreeze comes out of high pres

7. Turn water source on. NOTE: Failure to do so could cause damage to the pump. 8. Start engine. See Engine Owners Manual for correct procedure. NOTE: If the engine does not start after two pulls, pull the trigger to relieve the pressure. 9. Depress trigger on gun to start water flow. NOTE: Stand on a stable surface and grip gun/spray wand firmly with both hands. Expect the gun to kick when triggered. 10. Release trigger to stop water flow. 11. Adjust spray for the task being performed by changi

• Operating the pressure washer in an ex- plosive environment could result in a fire. • Operate and fuel equipment in well venti- lated areas free from obstructions. Equip areas with fire extinguisher suitable for gasoline fires. 3- ENG A08058 HAZARD RISK OF EXPLOSION OR FIRE (continued) HOW TO PREVENT IT WHAT CAN HAPPEN • Materials placed against or near the pressure washer can interfere with its proper ventilation features causing overheating and possible ignition of the materials. • Never ope

All decisions of Porter-Cable Corporation with regard to this limited warranty shall be final. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. RESPONSIBILITY OF ORIGINAL PURCHASER (initial User): • To process a warranty claim on this product, DO NOT return it to the retailer. The product must be evaluated by a Porter-Cable Authorized Warranty Service Center. For the location of the nearest Porter-Cable Authorized Warranty Service

Turn the turret to the desired nozzle. 3. Pull quick connect coupler back and place nozzle into quick connect coupler. 3. Push quick connect coupler over nozzle to secure in place. HOW TO SIPHON CHEMICALS/CLEANING SOLVENTS Siphoning chemicals or cleaning solvents is a low pressure operation. NOTE: Use only soaps and chemicals designed for pressure washer use. Do not use bleach. To siphon chemicals: 1. Press chemical hose onto barbed fitting located near high pressure hose connection of pump as s

5. Add *RV antifreeze to hose as shown. 6. Pull engine starter rope slowly several times until antifreeze comes out of high pressure hose connection of pump. 7. Remove short hose from water inlet of pump. 8. Reconnect spark plug wire. 9. Drain all water from high pressure hose, coil it, and store it in cradle of the pressure washer handle. 10. Drain all water from spray gun and wand by holding spray gun in a vertical position with nozzle end pointing down and squeezing trigger. Store in gun/hose

• During operation, touch only the control surfaces of the pressure washer. Keep children away from the pressure washer at all times. They may not be able to recognize the hazards of this product. RISK OF INJURY OR PROPERTY DAMAGE WHEN TRANSPORTING OR STORING HAZARD WHAT CAN HAPPEN HOW TO PREVENT IT • Fuel or oil can leak or spill and could result in fire or breathing hazard, serious injury or death can result. Fuel or oil leaks will damage carpet, paint or other surfaces in vehicles or trailers

Never pull water supply hose to move pressure washer. This could damage hose and/or pump inlet. DO NOT use hot water, use cold water only. Never turn water supply off while pressure washer engine is running or damage to pump will result. DO NOT stop spraying water for more than two minutes at a time. Pump operates in bypass mode when spray gun trigger is not pressed. If pump is left in bypass mode for more than two minutes internal components of the pump can be damaged. If you do not understand

Turn the turret to the desired nozzle. 3. Pull quick connect coupler back and place nozzle into quick connect coupler. 3. Push quick connect coupler over nozzle to secure in place. HOW TO SIPHON CHEMICALS/CLEANING SOLVENTS Siphoning chemicals or cleaning solvents is a low pressure operation. NOTE: Use only soaps and chemicals designed for pressure washer use. Do not use bleach. To siphon chemicals: 1. Press chemical hose onto barbed fitting located near high pressure hose connection of pump as s