Войти: For preprogrammed recording, the VCR needs the following data, which must be stored in a TIMER block: - Date for recording - Program number of the transmission - Start/stop time for recording These data can be copied directly to the VCR from the corresponding program survey of the teletext service. The PDC (RCF Recorder Control Function) data transmitted via Teletext automatically enable correct recording of the required program. For PDC test purposes this pattern generator offers page numb
2, 3/99 © 1998, 1999 Fluke Corporation, All rights reserved. Printed in Germany. All product names are trademarks of their respective companies. Please note In correspondence concerning this instrument, please quote the type number and serial number as given on the type plate. Bitte beachten Bei Schriftwechsel über dieses Gerät wird gebeten, die Typennummer und die Gerätenummer anzugeben. Diese befinden sich auf dem Typenschild an der Rückseite des Gerätes. Noter s.v.p. Dans votre corresp
The result is a reduction in cross color interference and an improvement in the picture quality. The R-G-B output offers the primary colors red, green, and blue including composite sync and sub-carrier signals at 5 BNC sockets at the rear side. Service is done at the component level, so it is not necessary to exchange a complete module. In addition the mechanical concept allows quick access to all parts for service purposes; all units are plugged into the motherboard. (GB) 2-2 GENERAL PM 541
Example: ALAR:RHUM1:SENS:ENAB 1 The RHUMidity suffix,
Materials for Cleaning the High Range Piston Cylinder 1. Prepare a clean work area near a running tap water source. 2. Prepare several sets of folded wipers as shown in Figures 6-2 through 6-4. Two wipers can be folded together for wiping the outside of the piston and cylinder. Prepare several twisted wipers as shown in Figures 6-10 through 6-12 to wipe the bore of the cylinder. 3. Disassemble the piston/cylinder assembly. 4. Insert the retaining clip from the bottom of the piston into the insta
This would be the connection at a branch circuit. Power Recorder Power Type Diagrams SD ETHERNET POWER 1750 POWER RECORDER ON BUSY LINK 100-240 V 47-63Hz BA C N VOLTAGE CURRENT A/L1 NGND B/L2 azd03f.eps Figure 6. One-Phase Split Phase Example: A North American residential installation at the service entrance. Operators Manual SD ETHERNET POWER 1750 POWER RECORDER ON BUSY LINK 100-240 V 47-63Hz BA C N VOLTAGE CURRENT B/L2 A/L1 C/L3 NGNDSource GND OC/L3 OA/L1 OB/L2 azd04f.eps Figure 7. Three-Phase
10 ©2004, 2005 Fluke Corporation, All rights reserved. Printed in U.S.A. All product names are trademarks of their respective companies Fluke Biomedical Radiation Management Services 6045 Cochran Road Cleveland, Ohio 44139 440.498.2564 120 Andrews Road Hicksville, New York 11801 516.870.0100 Table of Contents Section 1: General Information................................................................................... 1-1 1.1 Introduction ......................................................
The program will be generated and the display will show the first step. 8. Press the Name [F6] key to edit the name of the program. See next section, Chapter 4, Changing the Name of a Program, for creating a user-defined program name. Local Operation Menu Changing the Name of a Program 1. The name of an existing program is changed from the Program Menu. From the Main Menu (press PREVIOUS until the Main Menu appears), press Menu [F6] | Program [F4]. In addition to changing the name of an existing
°C and °F To toggle between °C (Celsius) and °F (Fahrenheit) measurements, press the Menu softkey until °C or °F appears as the left softkey function. Press the corresponding softkey to change between the measurements. Min, Max, Avg, Differential The thermometers can measure minimum (MIN), maximum (MAX), average (AVG), or differential (.) temperatures each time a reading is taken. These values are not shown if a thermocouple is plugged into the thermometer. To turn on the Min Max mode: 1. Press
