The side panels have keyhole-shaped cutouts. Push the side bungs which blank off the charge control knob aperture, panels over the screws and push downwards. 20. Screw the side panels tightly (screw A). DO NOT OVERT1GH- 21. Fit the charge control knob and room thermostat control knob TEN THE SCREWS. Assembly is now finished. over their spindles in the right-hand side panel. 5 23. Finally, disconnect the electricity supply and connect each supply cable to a suitable double pole switch adjace

No loops of cable should be left behind or underneath the unit. Core space cover 5. Stability The heater must be fixed securely to a solid wall to prevent movement. A screw with wall plug is provided in the accessory pack to secure the heater. The assembled heater must be able to resist a horizontal pull of at least 200N on its upper edge without toppling or shifting. If the required stability cannot be achieved with the supplied accessories, e.g. in the case of light-construction walls, th

Note also the information given on the appliance. 1. THIS HEATER IS VERY HEAVY, BEFORE INSTALLING ENSURE THAT THE SUPPORTING SURFACE IS STRONG ENOUGH TO SUPPORT THE WEIGHT OF THE HEATER (SEE BELOW “INSTALLED WEIGHTS“). IN ORDER TO MAINTAIN STABILITY AND TO ENSURE ITS FUTURE SAFETY IN USE, IT IS ESSENTIAL THAT IT IS SECURED TO A SOUND WALL BY MEANS OF THE FIXING SUPPLIED. IRREGULAR SURFACES SUCH AS MAY RESULT FROM CARPETS OR TILED SURROUNDS PARTIALLY PROTRUDING UNDER THE HEATER SHOULD BE AVOIDED

Able to regulate input with direct acting heat flexibility, the SFHA Sensair is more effective at retaining heat than a conventional storage heater. ” Able to operate on virtually any tariff and with superior high performance insulation levels, it achieves higher SAP and NHER ratings than manual input storage heaters. Key features • Combines electric storage fan heating, direct acting heating and fanned heat output with simple controls • Fully automatic heat storage - no user adjustment required

* TSR6AW/MW have no user controls and are IPX2 rated (drip-proof) ChargeCharge Acceptance (7 hrs)Acceptance (8 hrs) • Elements (storage) - mineral insulated stainless steel sheathed • Insulation - opacified silicaceous aerogel and mineral fibre mat • Storage Core - high density iron oxide compound • Controls* (Output) - manually adjustable thermostat controlling output damper. • Controls (Input) - hydraulic charge control thermostat, manually adjustable • Protection - two level thermal safety ov

REPLACING THE GREASE FILTER 1. Push the wire clips to one side and remove (Fig.10). Fig.10 2. Remove the saturated grease filter. 3. Place the new grease filter in the filter grille (Fig.11). Fig.11 4. Replace the retaining clips. 5. Close the grille panel. THE CARBON FILTER ( Recirculation only) The activated carbon filter absorbs odours arising from the cooking. In use, the filter will slowly become saturated and gradually less effective. The filter will normally require changing every four mo

The cut-out device will reset itself when the fan motor has cooled significantly. NOTE: This hood has been designed and approved for installation over an electric hob with a maximum input of 7kW or a gas hob with a maximum input of 10kW when fitted in accordance with the heights recommended above. Your Cooker Hood can be installed either for recirculation back to the room or extraction through an outside wall. When used in the extraction mode the Cooker Hood ducting must not be connected to a fl

Electrical Requirements Any permanent electrical installation must comply with the latest I.E.E. Regulations and local electricity company regulations. For your own safety, this should be undertaken by a qualified electrician eg. your local electricity company or a contractor who is on the roll of the National Inspection Council for Electrical Installation Contracting (NICEIC). Please ensure that when the appliance is installed it is easily accessible for the engineer in the event of a breakdown

Fix the wall brackets. 2. Fix the canopy hood. 3. Connect the hood to the mains supply ensuring that the canopy is functioning correctly. 4. Select the type of installation, ie. ducting or recirculation. 5. Fix the chimney stack. NOTE: The hood is more efficient in the exhaust mode, therefore, this position should be selected during the warmer months of the year when no heating is being used. When the room is being heated, if the recycle position is selected heat will not be wasted. Installing y

Do install the hood at the correct height, allowing at least the minimum distance above a cooking appliance (see page 5). Fan Speed The right slider enables you to select the fan speed. Your Cooker Hood has three speeds to give you the correct extraction level to suit your cooking conditions. Position 1 should be selected when simmering or when using only one pan. Position 2 should be selected for normal cooking up to four pans. Position 3 should be selected when frying or cooking food with stro