Оценок - 2, средний балл: 5
(
)
)
|
Фрагмент инструкции
Electrical Requirements Any permanent electrical installation must comply with the latest I.E.E. Regulations and local electricity company regulations. For your own safety, this should be undertaken by a qualified electrician eg. your local electricity company or a contractor who is on the roll of the National Inspection Council for Electrical Installation Contracting (NICEIC). Please ensure that when the appliance is installed it is easily accessible for the engineer in the event of a breakdown. INCORRECT INSTALLATION COULD AFFECT THE SAFETY OF THE APPLIANCE If the Cooker Hood is permanently wired in, it must be via a suitable double pole isolating switch placed in a readily accessible position adjacent to the unit. Electrical Connection Before connecting to the mains supply ensure that the mains voltage corresponds to the voltage on the rating plate, inside the Cooker Hood. WARNING: THIS APPLIANCE MUST NOT BE EARTHED! It is fitted with a 2 core mains supply cable and must be permanently connected to the electricity supply via a double pole switch having 3mm minimum contact gap on each pole. A Switched Fuse Connection Unit to BS 1363 Part 4, is a recommended mains supply connection accessory to ensure compliance with the Safety Requirements applicable to fixed wiring instructions. DISCONNECT THE COOKER HOOD FROM THE MAINS SUPPLY BEFORE CARRYING OUT ANY KIND OF MAINTENANCE OR CLEANING. WARNING: CHILDREN SHOULD NOT BE ALLOWED TO PLAY WITH THE APPLIANCE OR TAMPER WITH THE CONTROLS. CE marking certifies that this appliance conforms to the following EEC directives:Low Voltage Equipment - 72/23/EEC Electromagnetic Compatibility - 89/336/EEC Contents Page Electrical Requirements 2 Get to know your Cooker Hood 4 Installing your Cooker Hood 5-8 Operating your Cooker Hood 9 The Controls Do’s and Don’ts Caring for your Cooker Hood 10-11 Filters and their Replacement Cleaning How to Replace the Light Troubleshooting 12 Key Contacts Back Cover Appliance manufactured in EU. Retention of the Instruction Book This Instruction Book must be kept handy for reference as it contains important details on the safe and proper use of the appliance. If you sell or pass the appliance to someone else, or move house and leave it behind, make sure this Book is also provided so the new owner can become familiar with the appliance and safety warnings. If the book is lost or damaged a copy may be obtained from: GDA Ltd., Morley Way, Peterborough, PE2 9JB 3 Get to know your Cooker Hood. This Cooker Hood is available in a 90cm width Model CRC90 or a 60cm width Model CRC65. This instruction booklet covers both Models. Unpacking Before installation, ensure that you have removed all packing pieces. Ensure the fixing kit, ducting spigots and literature pack are retained with the hood. Filter Grilles Chimney Section Recirculation Grilles Hob Lights Controls Performance Table No. of speeds 3 Pressure Pa 370 Capacity (m3/h) MIN MAX 210 400 Noise Level (dBA) MIN MAX 48 60 (Depending on Model) Dimensions Height adjustable from: 685mm up to 850mm Width 600mm or 900mm (Depending on Model) Depth 515mm All measurements are in millimetres. Installing your Cooker Hood SAFETY WARNINGS: THIS COOKER HOOD IS DESIGNED FOR DOMESTIC USE ONLY. When installed above a cooking appliance, the distance between the surface of the hob elements and the lower grille of the chimney hood must be as follows: Minimum 650mm - over an electric hob. Minimum 700mm - over a gas or mixed fuel hob. This chimney hood is not suitable for installation above a cooking appliance with a high level grill. THERMAL CUT-OUT: The fan motor of this appliance incorporates a thermal cut-out device which will operate if the hood is installed below the minimum recommended heights listed above, or if the motor becomes overheated. If the cut-out device is activated, switch off the fan motor and allow the hood to cool. The cut-out device will reset itself when the fan motor has cooled significantly. NOTE: This hood has been designed and approved for installation over an electric hob with a maximum input of 7kW or a gas hob with a maximum input of 10kW when fitted in accordance with the heights recommended above. Your Cooker Hood can be installed either for recirculation or extraction through an outside wall. When used in the extraction mode the Cooker Hood ducting must not be connected to a flue which is used for exhausting fumes from a central heating flue or water heating flue. IMPORTANT: The exhaust air must not be expelled through a smoke or waste-gas chimney which is in use or through a shaft used for ventilating rooms or into the cavity of a cavity wall or into a cupboard above the cooker hood. If the room contains, a flued fuel burning appliance, such as a gas or oil fired central heating boiler which is not of the ‘Balanced Flue’ type, you should make sure that there is adequate air inlet into the room at all times, so that fumes from the boiler are not drawn back into the room by the Cooker H...
Эта инструкция также подходит к моделям:Вентиляторы - CRC65 (92.55 kb)