x 20.75 Cyl. Assy. Bucket 24314 3.0 Dia. x 30.00 Cyl. Assy. Lift 811572_3/8 x 15" Hose 3/4 MORB x 3/4 SWFJIC 811471 3/8 x 20" Hose 3/4 MORB x 3/4 SWFJIC 811466 3/8 x 24" Hose 3/4 MORB x 3/4 SWFJIC 812947_3/8 x 22" Hose 3/4 SWFJIC x 3/4 SWFJIC 112833 Tubing - Lift Cyl. Bottom Raise 112834 Tubing - Lift Cyl. Top Drop 112937 Tubing - Lift Cyl. Common (31.0") 112835 Tubing - Bucket Cyl. Bottom Rollbk 112836 Tubing - Bucket Cyl. Top Dump 112837 Tubing - Bucket Cyl. Cross Tube 812128 Elbow 90

If the loader is lowered from this position, the bucket will extend as the quick attach contacts the rollback stop and the circuit goes through relief as described in note 2. The relief valve is factory set at 3250 PSI cracking pressure and is capable of bypassing 10-15 GPM. If loader lock-up should occur due to a low tractor relief setting, higher inlet flows or return line restrictions, the relief valve may be backed off slightly until the lock-up condition is overcome (counterclockwise turn

Any sample or model is for illustrative purposes only and does not create an Express Warranty that the goods conform to sample or model shown. t The purchaser is solely responsible for determining suitability of goods sold. This warranty is expressly in lieu of all other warranties expressed or implied. Buhler Manufacturing will in no event be liable for any incidental or consequential damages whatsoever, nor for any sum in excess of the price received for the goods for which liability is clai

. 2. Move and turn tractor at low speed. 3. Carry loader arms at a low position during transport. ■ 4. Lower loader arms, stop engine and lock brakes before leaving operator seat. 5. Do not stand or work under raised loader, unless properly ' supported. 6. Add recommended wheel ballast or rear weight for stability. 7. Move wheels to widest recommended settings to increase stability. 8. Do not handle large round bales or other shiftable objects unless loader is equipped with a grapple fork

x 20.75 Cyl. Assy. Bucket 24314 3.0 Dia. x 30.00 Cyl. Assy. Lift 811572_3/8 x 15" Hose 3/4 MORB x 3/4 SWFJIC 811471 3/8 x 20" Hose 3/4 MORB x 3/4 SWFJIC 811466 3/8 x 24" Hose 3/4 MORB x 3/4 SWFJIC 812947_3/8 x 22" Hose 3/4 SWFJIC x 3/4 SWFJIC 112833 Tubing - Lift Cyl. Bottom Raise 112834 Tubing - Lift Cyl. Top Drop 112937 Tubing - Lift Cyl. Common (31.0") 112835 Tubing - Bucket Cyl. Bottom Rollbk 112836 Tubing - Bucket Cyl. Top Dump 112837 Tubing - Bucket Cyl. Cross Tube 812128 Elbow 90

Loose connections. Worn or damaged O-ring wiper seal in cylinder rod end. Worn or damaged O-rings in valve. Replace damaged parts. Tighten fittings. Install a seal repair kit. Install an O-ring repair kit. Insufficient lift capacity Improper hydraulic pump operation. Repair or replace pump. Load is greater than boom lift capacity. Check loader specifications. Internal boom cylinder leakage. Replace any worn parts and install a seal repair kit. Improper hydraulic valve operation. Repair or repla

Hoses should be connected in such a manner that pushing forward on valve handles lowers the boom or dumps the bucket. CAUTION: Always connect boom hoses to float section. Weight added to rear of tractor provides better traction and an easier, more efficient loader operation. Extra weight, along with widening the rear wheels, reduces the risk of roll-over. /f\ I WARNING I The smaller the tractor is, the easier it will roll. We recommend that weight be added to rear tires with liquid or by the

(mm) Vtfench Sze (mm) Bolt Head Q O O Class 4.6 (ft-lbs) (NM) Class 8.8 (ft-lbs) (NM) Class 9.8 (ft-lbs) (NM) 8 13 7.3 10 21.1 29 10 16 14.5 20 42 57 12 18 25 34 74 100 73 99 14 21 40 54 118 160 116 157 16 24 62 84 167 226 181 245 20 30 122 165 325 440 22 33 443 600 24 36 211 286 563 763 27 41 821 1112 30 46 418 566 1119 1516 *Use 80% of the specified torque value for plated lubricated fasteners. 2 Pre-delivery Check List Before delivering this equipment pleas

If this is not done, the frame will not remain standing. _ A IMPORTANT! Always remove the loader on firm, level ground (away from children’s play areas and high traffic areas). This makes attaching and removing much faster and easier. It also makes the free standing loader more stable. _'_ Trouble Shooting PROBLEM POSSIBLE CAUSE REMEDY Loader slow and/or will not dump. Quick couplers leaking. Hydraulic oil too heavy. Oil filter plugged. Hydraulic pump worn. Oil line restricted or leaki

The TSL feature maintains the bucket level, but as required the bucket can be manually rolled back approximately 20 degrees to allow for increased bucket capacity. If the loader is lowered from this position, the bucket will extend as the quick attach contacts the rollback stop and the circuit goes through relief as described in note 2. ■ . v The relief valve is factory set,at 3250 PSI cracking pressure and is capable of bypassing 10-15 GPM. If loader lock-up should occur due to a low tracto