Box 32270 Louisville, KY 40232-2270 Phone: (502) 587-1292 Sales Fax: (502) 585-3625 Part No. AJ1031 Service/Parts Fax: (502) 681-1275 February 2005 Installation Table of Contents Model Identification ........................................................................... 3 Safety Information.............................................................................. 5 Explanation of Safety Messages........................................................... 5 Important Safety Instructions .

The currents listed are rated for system voltage ranges of 110 – 220 and 220 – 240. ** Rated Amperes are to be used to determine incoming conductor size and short-circuit protection. Rated amperes are figured in accordance with the 1981 NATIONAL ELECTRIC CODE, Sections 430-22 and 430-24. Table 2 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT AJ1031 Installation Overall Dimensions and Connecting Data SCR97N OPENOPENCLOSECLOSECLOSECLOSESTEAM INLETSTEAM INLET 36-7/8 in. (93.7 c

Replace Coil Assembly. Gas turned OFF. Turn Manual Gas Valve ON. Line fuse or heater circuit fuse blown to unit. Replace fuse. Defective Door Switch. Replace Door Switch. Silicon Carbide Igniter not igniting gas. Must be 3/16” to 5/16” above burner. Replace Radiant Sensor. Air Switch not operating. Clean out lint compartment daily. Check Back Draft Damper for foreign objects, lint accumulation or other causes that may prevent damper from operating. Check duct work for lint build-up. Check instal

. Did you push the “start” control? 4. Has a fuse blown or a circuit breaker tripped? 5. Are the fuses tight? 6. Check for low voltage. DRYER WON’T HEAT 1. Is the dryer set for “cooling time” rather than “drying time”? 2. Are the gas valve in the dryer and the valve on the main gas line turned on? 3. Check for low or intermittant gas pressure. CLOTHES ARE NOT SATISFACTORILY DRY 1. Timed cycle—Did you allow enough heating time before the cool-down part of the cycle? 2. Is the lint screen blocked?

ELEVATIONS ABOVE 2,000 FEET Input ratings shown on the rating plate (serial tag) are for elevations up to 2,000 feet. For elevations above 2,000 feet, rating should be reduced at a rate of 4% for each 1,000 feet above sea level. Page 30 Two Timer Models—Figures 1, 2, and 3 (Illustrations) Page 31 Operating Instructions—Two Timer Models OPERATING INSTRUCTIONS—TWO TIMER MODELS OPERATING INSTRUCTIONS—TWO TIMER MODELS 1. After loading the dryer tumbler with the water washed clothes load, proceed to

THE WARRANTIES GIVEN ABOVE ARE EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED. CISSELL NEITHER ASSUMES, NOR AUTHORIZES ANY PERSON TO ASSUME FOR IT, ANY OTHER WARRANTY OR LIABILITY IN CONNECTION WITH THE MANUFACTURE, USE OR SALE OF ITS EQUIPMENT OR PARTS. For warranty service, contact the Distributor from whom the Cissell equipment or part was purchased. If the Distributor cannot be reached, contact Cissell. IDENTIFICATION NAMEPLATE The Identification Nameplate is located on the re

PRESSURE In figuring total length of pipe, make allowance for tees and elbows. HOUR (25 ft.) 7,62 m (50 ft.) 15,24 m (75 ft.) 22,86 m (100 ft.) 30,48 m (125 ft.) 38,1 m (150 ft.) 45,72 m 60,000 15000 3/4 3/4 3/4 3/4 3/4 3/4 80,000 20000 3/4 3/4 3/4 1 1 1 100,000 25200 3/4 3/4 1 1 1 1 120,000 30200 3/4 1 1 1 1 1 140,000 35200 3/4 1 1 1 1 1 1/4 160,000 40300 3/4 1 1 1 1/4 1 1/4 1 1/4 180,000 45300 1 1 1 1 1/4 1 1/4 1 1/4 200,000 50400 1 1 1 1/4 1 1/4 1 1/4 1 1/2 300,000 75600 1 1 1/4 1 1/4 1 1/2 1

FOR BEST DRYING: 1. Exhaust duct maximum length 14 feet of straight duct and maximum of two 90° bends. 2. Use 45° and 30° elbows wherever possible. 3. Exhaust each dryer separately. 4. Do not install wire mesh or other restrictions in the exhaust duct. 5. Use clean-outs in the exhaust duct and clean periodically when needed. 6. Never exceed 0.3 inches water column static pressure in the exhaust duct. 7. Inside surface of the duct must be smooth. 8. Recommend pop rivets for duct assembly. FOR BES

1. Make-up air from outside building may enter enclosure fromtop or side walls. Area of opening should be equal to 4-6times the sum of dryer duct areas. Provide 1 sq. ft. for each 6in. diameter; 2 sq. ft. for each 8 in. diameter; and 4 sq. ft. foreach 12 in. diameter. 2. Use constant diameter duct with area equal to the sum of dryerduct areas. EXAMPLE: 6-8 in. diameter duct = 1-19.6 in. diameter duct in area. Use 20 in. diameter duct or diameter to match tube- axial fan. 3. Enclosure (plenum) wi

(See illustration on next page.) 1. Make-up air from outside building may enter enclosure from top or side walls. Area of opening should be equal to 4 to 6 times the sum of dryer duct areas. Provide 1 square foot (.1m.) for each 6 inches (15.24 cm) diameter; 2 square feet (.2m.) for each 8 inches (20.3 cm) diameter; and 4 square feet (.4m.) for each 12 inches (30.5 cm) diameter. 2. Use constant diameter duct with area equal to the sum of dryer duct areas. EXAMPLE: 6-8 inches (20 cm) diameter duc