11 Dryer Controls At A Glance..............................12-13 Dryer Operating Tips............. 14 Dryer Exhaust Tips.................15 Replacing the Drum Light... 16 Reversing the Dryer Door.... 16 Water Use................................. 17 Care and Cleaning.................17 Storing the Maytag Neptune™ Super Stack.......... 17 Washer Operating Sounds.......................................18 Before You Call..................19-21 Warranty......................Back Page MAYT

The letters "I" and "O" were skipped. Designates significant part changes within the same year for this model. Base is 5 and this number advances for each change. Example: T-6 "T" indicates 2008. "6" indicates the first significant part change for 2008. Note About Ordering Parts Most assemblies cannot be ordered as complete units; parts in the assemblies generally must be ordered separately. 3 Material Abbreviations ALUMINUM AL = Aluminum COPPER CU = Copper PLASTIC ABS = Acrylonitrile -butadiene

Typical Wiring Diagram for 208-230/1/60 with Fan Cycling. Models 049-080; 10-16Models 008-040; 1-8Models 105-133; 21-26TERMINALBOARDT3T2T1208-230V/3 phase/60HzM1M2M3FAN MOTORS460V/3 phase/60Hz Diagram 4. Typical Wiring Diagram for 208-230-460/3/60 TERMINALBOARDT3T2T1208-230V/3 phase/60HzGNDT2BOARDTERMINALT1M1C1C1M2C2FCCCOMNCC2M3C3FCCCOMNCC3FAN MOTORSCONTACTOR COILSTHERMOSTATS OR PRESSURE CONTROLSCONTACTORSCONTROL CIRCUIT* Models 049-080; 10-16Models 105-133; 21-26460V/3 phase/60Hz Diagram 5. Typ

This combination allows for greater versatility and control when drying and styling hair • The top switch printed in red controls the temperature of the airflow as follows • II = high heat I = low heat 0 = off • The bottom switch printed in silver controls the airflow as follows • II = strong airflow I = gentle airflow • 0 = off • A combination of high temperature and strong airflow is ideal for fast drying • A lower temperature and gentle airflow settings give greater control when styling • Aft

dry towels and thin underwear separately). Type of material: Cotton (linen); synthetic textiles (easy care). Degree of drying: Cupboard dry, iron dry etc. Do not tumble dry: Woollens, silk, nylon stockings, delicate embroidery, fabrics with metallic decorations, bulky items such as sleeping bags, etc. Check that all fastenings are closed and that pockets are empty. Please ensure that there are no cigarette lighters in the wash. Turn laundry inside out. Pull the door handle. If the child safety l

¦ Do not use an exhaust hood with a magnetic latch. Improper venting can cause moisture and lint to collect indoors, which may result in: Moisture damage to woodwork, furniture, paint, wallpaper, carpets, etc. Housecleaning problems and health problems. 11 Plan Vent System Choose your exhaust installation type Recommended exhaust installations Typical installations vent the dryer from the rear of the dryer. Other installations are possible. B C D A E F G H A. Dryer E. Clamps B. Elbow F. Rigid me

Strip 5" (12.7 cm) of outer covering from end of cable, leaving bare ground wire at 5" (12.7 cm). Cut 1 .. ." (3.8 cm) from 3 remaining wires. Strip insulation back 1" ( 2.5 cm). Shape ends of wires into a hook shape. (2.5 cm) 5"(12.7 cm) When connecting to the terminal block, place the hooked end of the wire under the screw of the terminal block ( hook facing right), squeeze hooked end together and tighten screw, as shown. 1. Remove center silver-colored terminal block screw. 2. Remove neutral

It is important that you remove only the 6 indicated screws. 5. Lift the inner door assembly off of the outer door assembly. Unsnap the handle from the outer door assembly, move it to the other side, and snap in. Set the outer door assembly aside. Reverse the hinge and hinge bracket 1. Place the inner door, screw head side up, on the work surface. 2. Remove the 4 screws that hold the hinge to the door. 3. Remove the 2 screws that hold the handle bracket to the door. 4. Move hinge to the other si

A thermistor (electronic temperature sensor) and moisture sensing strips in the dryer drum help measure the amount of moisture in the clothes as they tumble. An electronic control determines the load type to help save time, avoid overdrying, and increase the accuracy of the end dryness level. After the first 5 minutes of an automatic cycle, the estimated time display will adjust based on the approximate load size, cycle, dryness level selected and amount of moisture left in the clothes. When the