Оценок - 1, средний балл: 4
(
)
)
|
Фрагмент инструкции
(mm) Vtfench Sze (mm) Bolt Head Q O O Class 4.6 (ft-lbs) (NM) Class 8.8 (ft-lbs) (NM) Class 9.8 (ft-lbs) (NM) 8 13 7.3 10 21.1 29 10 16 14.5 20 42 57 12 18 25 34 74 100 73 99 14 21 40 54 118 160 116 157 16 24 62 84 167 226 181 245 20 30 122 165 325 440 22 33 443 600 24 36 211 286 563 763 27 41 821 1112 30 46 418 566 1119 1516 *Use 80% of the specified torque value for plated lubricated fasteners. 2 Pre-delivery Check List Before delivering this equipment please complete the following check list. 1. The loader has been installed using the appropriate mounting kit for the tractor and loader. — 2. The hydraulic system installed is appropriate for the tractor and loader | | 3. The loader is properly installed. | | 4. All bolts are tightened to the torque specifications shown in the torque chart. | ] 5. All safety decals are readable. 6. The loader has been tested and operates properly. i—i 7. The operator’s manual has been delivered to the owner who has been instructed on the safe and proper use I—I of the loader. • ' ■ ■ V Dealer’s Signature____ This check list is to remain in this Owner’s Manual and is the responsibility of the dealer to complete it before delivery to the customer. Loader Identification Diagram (HSL Model Shown) For further details refer to Loader Mainframe and Subframe diagrams. Hydraulic (Hose Kit) Identification Diagrams Hose Kit “A” Loader Powered by the tractor remotes. Consists of four hoses leading from loader tubing to tractor remote couplers Hose Kit “B” Loader operated by an external OC or CC valve that is powered from the tractor remotes Consists of 4 hoses leading from loader tubing to external mounted valve and 2 hoses from valve to tractor couplers. Use the valve type shown with hose kit “B”. Hose Kit “C” Loader operated by an external valve that is plumbed into the tractor hydraulic system. Consists of 4 hoses leading from loader tubing to external mounted valve plus the necessary fittings, hoses and adapter blocks (if necessary) to tap into tractor hydraulic system. Use valve type shown with hose kit “C”. 5 General Instructions and Information As with any piece of equipment, the care with which your loader is operated and maintained will greatly affect it’s life and the safety of the people using it. 1. Keep all pivots well lubricated for longer bushing life. Inspect every 500 hours of operation for wear. 2. Periodically check all bolts for tightness. If any bolt is damaged, replace it with a bolt of equivalent grade or strength. 3. Follow the recommendations of the tractor manufacturer in regards to the quantity of oil used. 4. Check oil level frequently to ensure the system is full. 5. When making an oil check, be sure lift cylinders are retracted. % 6. Before operating the loader, particularly if the loader is left standing for any length of time, check the hydraulic system and oil level. ^ 7. When installing hydraulics, follow the circuit carefully. See hydraulic hook-up section and make sure the hoses do not contact any hot manifolds or sharp edges on tractor. After assembly, raise the loader slowly and check to make sure that the hoses do not bind in all positions. The pressure of the relief and open center valves is set at the factory. Do not tamper with the setting, serious injury to the operator or damage to the loader or tractor hydraulics may occur. Warranty will be void if the loader is operated above recommended pressure. 9. When servicing any hydraulic components, care must be taken to prevent any foreign matter from entering the system. 10. Do not neglect oil leaks. Leaks affect loader operation, are dangerous and can result in personal injury or damage to the hydraulic system. 11. Never leave the cylinder shafts exposed when loader is not in use, 12. Worn or damaged components should be replace as soon as possible with only the manufacturer’s recommended component or equivalent. CAUTION DO NOT use bucket in dumped position for bulldozing. This will only impose severe shock loading on the bucket cylinders and make it more difficult to maintain a level grade. Attaching the Loader to Your Tractor (Continued) When the hook is lined up, dump or roll back the bucket to lower or raise the subframe upright to align with the mounting boot. Continue to drive the tractor forward until the subframe uprights are seated in the boot. Secure the subframe uprights with the bolts and washers. Torque to 500 ft-lbs. IMPORTANT: When mounting for the first time, the front hook bolts will have to be tightened after positioning the hook directly over the mounting boss (most rearward position). _■_ Raise the loader and lock the support stand tubes into the up position. NOTE: When mounting for the first time, raise the loader slowly and check to make sure that the hoses do not bind or become pinched in all positions. Work the loader and bucket up and down to work out all the air in the hydraulics. Check a...
Эта инструкция также подходит к моделям:Сушильные машины - 695 (2.62 mb)
Сушильные машины - 695 HSL (2.62 mb)