Оценок - 2, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
. 2. Move and turn tractor at low speed. 3. Carry loader arms at a low position during transport. ■ 4. Lower loader arms, stop engine and lock brakes before leaving operator seat. 5. Do not stand or work under raised loader, unless properly ' supported. 6. Add recommended wheel ballast or rear weight for stability. 7. Move wheels to widest recommended settings to increase stability. 8. Do not handle large round bales or other shiftable objects unless loader is equipped with a grapple fork. 9. Do not use loader to move or carry people. 10. Stay away from power lines. Electrocution can occur without direct contact. 11. Review safety instructions annually. , 11M1J 7 General Instructions and Information As with any piece of equipment, the care with which your loader is operated and maintained will greatly affect it's life and the safety of the people using it 1. Keep all pivots well lubricated for longer bushing life. Inspect every 500 hours of operation for wear. 2. Periodically check all bolts for tightness. If any bolt is damaged, replace it with a bolt of equivalent grade or strength. 3. Follow the recommendations of the tractor manufacturer in regards to the quantity of oil used. 4. Check oil level frequently to ensure the system is full. 5. When making an oil check, be sure lift cylinders are retracted. 6. Before operating the loader, particularly if the loader is left standing for any length of time, check the hydraulic system and oil level. 7. When installing hydraulics, follow the circuit carefully. See hydraulic hook-up section and make sure the hoses dip not contact any hot manifolds or sharp edges on tractor. After assembly, raise the loader slowly and check to make sure that the hoses do not bind in all positions. The pressure of the relief and open centre valves is set at the factory. Do not tamper with the setting. Serious injury to the operator or damage to the loader or tractor hydraulics may occur. Warranty will be void if the loader is operated above recommended pressure. 8. When servicing any hydraulic components, care must be taken to prevent any foreign matter from entering the system. 9. Do not neglect oil leaks. Leaks affect loader operation, are dangerous and can result in personal injury or damage to the hydraulic system. 10. Never leave the cylinder shafts exposed when loader is not in use. 11. Worn or damaged components should be replaced as soon as possible with only the manufacturer's recommended component or equivalent. Operating Suggestions For Loading NOT THIS! When handling heavy loads, be sure to lower lift arms slowly. This is known as feathering the hydraulic lever. If load is lowered too fast and stopped suddenly, excessive shock loads are created which can damage loader or tractor. When loading bucket, drive straight into material. Attempting to turn tractor while loading bucket can cause damage to both the loader and tractor. NOTE: Bottom surface of bucket is parallel to line on motion. Work both levers back to direct pressure to both cylinders. Combined action of lift and bucket cylinders increases loading efficiency. DO THIS! A straight bottom offers more resistance to lift. To increase loading efficiency, minimize angle of turn and length to run between pile and spreader. Leave material which drifts over side of bucket for final clean-up. Attaching the Loader to Your Tractor (Continued) 6. When the hook is lined up, dump or roll back the bucket to lower or raise the subframe upright to align with the mounting boot. 7. Continue to drive the tractor forward until the subframe uprights are seated in the boot. “t 8. Secure the subframe uprights with the bolts and washers. Torque to 500 ft-lbs. IMPORTANT: When mounting for the first time, the front hook bolts will have to be tightened after positioning the hook directly over the mounting boss (most rearward position). 9. Raise the loader and lock the support stand tubes into the up position. NOTE: When mounting for the first time, raise the loader slowly and check to make sure that the hoses do not bind or become pinched in all positions. Work the loader and bucket up and down to work out all the air in the hydraulics. Check and refill the tractor's hydraulic system. 13 Removing the Loader from Your Tractor WARNING ! When removing the loader, it must be fitted with a bucket or other suitable attachment to give the frame stability after removal. If this is not done, the frame will not remain standing. " " ' ------------------------I IMPORTANT ! Always remove the loader on firm, level ground (away from children's play areas and high traffic areas). This makes attaching and removing much faster and easier. It also makes the free standing loader more stable. 1. Raise the loader, lower support stand tubes and i lock into position. ’ 2. Lower the loader until the stand tubes are firmly on the ground and then dump the bucket so that it is also firml on the ground. There should be...
Эта инструкция также подходит к моделям:Сушильные машины - 395 (892.26 kb)