Войти:
Скачали: 0   Размер: 637 kb   Производитель: Harbor Freight Tools  
Категория: Строительные пистолеты
@name

The Tool should not fire if the Safety Nosepiece is not pressed against the workpiece. Full Sequential Safety Trip Mechanism Testing Procedure TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION: Empty the tool before this procedure. Point the tool at a piece of scrap wood when testing. 1. Disconnect the tool from the air supply. 2. Empty the Nail Canister (82) of fasteners. 3. Check that the Trigger (47) and the Safety Nosepiece move freely, without sticking. 4. Connect the air supply to the to

Скачали: 2   Размер: 257 kb   Производитель: Harbor Freight Tools  
Категория: Строительные пистолеты
@name

19. Store idle tools out of reach of children and other untrained persons. Tools are dangerous in the hands of untrained users. Never allow children to come in contact with this product. 20. Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained tools with a sharp cutting edge are less likely to bind and are easier to control. Do not use a damaged tool. Tag damaged tools “Do not use” until repaired. 21. Check for misalignment or binding of moving parts, breakage of par

Скачали: 2   Размер: 1 mb   Производитель: Harbor Freight Tools  
Категория: Строительные пистолеты
@name

(See Figure B.) LOADING COIL NAILS WARNING: Always wear ANSI approved impact safety goggles when reloading or performing any other maintenance on this tool. Other people in the work area must also wear ANSI approved impact safety goggles. WARNING! Make sure the Nailer is not attached to the air hose when loading the tool. 1. To open the Magazine Cover (91), press down on the Latch (57) and swing the Door (32) open. Then, swing the Magazine Cover open. (See Figure C.) MAGAZINE COVER (91) LATCH (5

Скачали: 5   Размер: 841 kb   Производитель: Harbor Freight Tools  
Категория: Строительные пистолеты
@name

3. After the Nails reach the nose of the tool, close the Magazine (60) making sure the Retaining Spring (58) clicks shut. See Figure 1. Operating the Nailer 1. Attach the Nailer to the air supply at the Air Inlet (38). Start your compressor and check the pressure making sure it is set at the recommended 55-95 PSI and not to go over the maximum 95 PSI. 2. To fire, place the nose of the Nailer on the workpiece. The Nailer should not fire if the nose is not depressed. Once depressed, gently and bri

Скачали: 5   Размер: 124 kb   Производитель: Harbor Freight Tools  
Категория: Строительные пистолеты
@name

Please confirm it before installation. 2. If the car interior is extremely hot, as after being parked in the sun, do not use the player until the car has been driven fora while to cod off the interior. 3. Press the OPEN button to flip down the front panel (see fig.1), Slide the guide knob to remove the right side first, then take away the front panel, (see fig.2) and put it in the protective case (see fig.3) for safe keeping. 4. Install the front panel back into its bracket and then push it

Скачали: 9   Размер: 632 kb   Производитель: Harbor Freight Tools  
Категория: Строительные пистолеты

1. Disconnect tool from air hose, empty Magazine A (66) of staples, release any built-up air pressure, and leave the magazine open, as explained above. 2. Safety Cover Bolt (53)FIGURE 1While doing this step and the next, hold the Stapler pointed away from you and any other people or fragile objects - see Figure 1. Remove all three Safety Cover Bolts (53) on the Safety Cover (54). 3. FIGURE 2Safety (52) Safety Cover (54) Lift the Safety Cover (54) off the top of the stapler - see Figure 2. 4. FIG

Скачали: 4   Размер: 632 kb   Производитель: Harbor Freight Tools  
Категория: Строительные пистолеты

The warnings and precautions discussed in this manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. Vibration Precautions This tool vibrates during use. Repeated or long-term exposure to vibration may cause temporary or permanent physical injury, particularly to the hands, arms and shoulders. To reduce the risk of vib

Скачали: 0   Размер: 632 kb   Производитель: Harbor Freight Tools  
Категория: Строительные пистолеты
@name

Squeeze the Trigger (39). The tool should not cycle (fire). If it cycles (fires), stop immediately and take the tool to a qualified service technician. 8. Depress the Safety (52) against the workpiece and squeeze the Trigger (39). The tool must cycle (fire) once only. Release the trigger and squeeze it again. The tool must cycle (fire) once only. REV 10a With the Trigger held, carefully lift the nailer and press it against the workpiece again. The tool must not cycle (fire). If it fails to act i

Скачали: 3   Размер: 788 kb   Производитель: Harbor Freight Tools  
Категория: Строительные пистолеты
@name

makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper installation, normal wear and tear, or to lack of maintenance. W

Скачали: 1   Размер: 457 kb   Производитель: Harbor Freight Tools  
Категория: Строительные пистолеты
@name

e. Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enables better control of the tool in unexpected situations. f. Use safety equipment. A dust mask, non-skid safety shoes and a hard hat must be used for the applicable conditions. Wear heavy-duty work gloves during use. Wear a full face shield if you are producing metal filings or wood chips. g. Always wear eye protection. Wear ANSI-approved safety goggles with side shields during use. h. Always wear he





Категории