Please read carefully before use. Manual de Instrucciones Información importante. Por favor, léala atentamente antes de usar la herramienta. Guide D’Utilisation Renseignements importants. Prière de lire attentivement avant d’utiliser. 348061 -oo POWERSHOT® STAPLE AND NAIL SELECTION GUIDE For best results the POWERSHOT Heavy Duty Staple and Nail Gun has been designed to use POWERSHOT Brand Heavy Duty .05” crown width staples and type 13 nails, 9/16” in length. It will also accept other stan

plate is located on the main housing of the tool. Record these numbers in the spaces below and retain for future reference. Model No. ___. ______ Type_ Serial No.__ Part No. 892256-992 IMPORTANT SAFETY INSTRUCTIONS WARNING: When using pneumatic tools, basic safety precautions should always be followed to reduce the risk of personal injury, including the following: READ AND FOLLOW ALL INSTRUCTIONS. There are certain applications for which this tool was designed. Porter-Cable strongly reco

Entangled or snarled hoses can cause loss of balance or footing. • Always keep fingers clear of nail track of magazine to prevent injury from inadvertent release of the pusher. (Fig. 18) • Refer to the Maintenance section for detailed information on the proper maintenance of the tool. • Always operate the tool in a clean, lighted area. Be sure the work surface is clear of any debris and be careful not to lose footing when working in elevated environments such as rooftops. • Do not use tool in th

Please check with the retailer for their specific return policy regarding returns that are beyond the time set for exchanges. 10 905013144 wo depth 11/28/06 7:43 AM Page 11 The second option is to take or send the product (prepaid) to a Black & Decker owned or authorized Service Center for repair or replacement at our option. Proof of purchase may be required. Black & Decker owned and authorized Service Centers are listed under "Tools-Electric" in the yellow pages of the phone directory. This wa

THIS PRODUCT IS COVERED BY US PATENT NOS. 6,705,503 AND 6,604,666. OTHER PATENTS PENDING. Black & Decker (U.S.) Inc., See ‘Tools-Electric’ 701 E. Joppa Rd. – Yellow Pages – Towson, MD 21286 U.S.A. for Service & Sales 11 905013144 wo depth 11/28/06 7:43 AM Page 12 GUIDE D’UTILISATION N. de catalogue FS1202BN / FS1802BN M MMMM E EEEE R RRRR C CCCC I IIII D DDDD ’ ’’’’ A AAAA V VVVV O OOOO I IIII R RRRR C CCCC H HHHH O OOOO I IIII S SSSS I IIII F FFFF I IIII R RRRR E EEEE S SSSS T TTTT O OOOO R RRR

you need assistance in locating any accessory please contact: Black & Decker (U.S.) Inc, User Services Department, 10 North Park Drive, P.O. Box 85/, Hunt Valley.. MD 21030-0857. ' ■ • (CAUTION: The use of any other fastener or attachment might be hazardous.) To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment should be performed by Black and Decker Service Centers or other qualified service organizations, always using Black & Decker replacement parts Black & Decker

Never load nails with the contact trip or trigger activated. 1. After reading and understanding this entire manual, connect tool to air supply. (Fig. 22) 2. Depress latch and slide magazine cover open. (Fig. 23) 3. Insert a strip of approved fasteners. (Fig. 24) Orient fasteners with points down in the magazine. 4. Push magazine cover closed. (Fig. 25) 5. Observe the low fastener indicator (A) Fig. 26 and reload as needed. 6. Adjust directional exhaust deflector (A) Fig. 27, so that the exhaust

4. Unplug charger, and remove the battery pack. Place the battery in the tool and be certain that it is inserted fully into the tool cavity until it “clicks” into place. NOTE: To remove the battery pack from the product, press down on the release button on the back of the battery (Figure 2) and pull out. Replace Pack The charger is designed to detect certain problems that can arise with battery packs which would be indicated by the red light flashing at a fast rate. If this occurs, re-insert bat

5. Insert fasteners into the side of the magazine. Be sure the fasteners ride on their tips in the nail channel as shown in figure 5A. 6. Push magazine closed until it locks in place. Actuating Tool WARNING: Always wear eye and ear protection when operating tool. To operate the nailer: 1. Disengage lock off. 2. Insert battery pack and lock in place. 3. Depress the contact trip firmly against the work surface. 4. Depress and maintain pressure on the trigger. CAUTION: A nail will fire each time th

The operator and all those persons in the general area should wear safety glasses with permanently attached side shields. Approved safety glasses are imprinted with the characters “Z87.1”. • Always wear appropriate personal hearing and other protection during use. Under some conditions and duration of use, noise from this product may contribute to hearing loss. • Always engage lock off first then disconnect battery pack from the tool whenever clearing a jam, performing any maintenance or repair,