3. After the Nails reach the nose of the tool, close the Magazine (60) making sure the Retaining Spring (58) clicks shut. See Figure 1. Operating the Nailer 1. Attach the Nailer to the air supply at the Air Inlet (38). Start your compressor and check the pressure making sure it is set at the recommended 55-95 PSI and not to go over the maximum 95 PSI. 2. To fire, place the nose of the Nailer on the workpiece. The Nailer should not fire if the nose is not depressed. Once depressed, gently and bri

The warnings and precautions discussed in this manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. Vibration Precautions This tool vibrates during use. Repeated or long-term exposure to vibration may cause temporary or permanent physical injury, particularly to the hands, arms and shoulders. To reduce the risk of vib

For technical questions and replacement parts, please call 1-800-444-3353 Specifications Air Inlet 1/4 ”-18 NPT Recommended Air Pressure 60 -100 PSI, 100 PSI Max. Magazine Capacity 100 Nails or 80 Staples Safety Feature Single Sequential Safety Trip Mechanism Nail Size .039-.042” Shank (18 Gauge), 5/8 ” -11/ 4 ” L Staple Size 1/4 ” Crown, .039-.042” Shank (18 Gauge), 1/2 ” -11/ 4 ” L Accessories Oil Dropper, 2 Wrenches, 1 Coupler Plug Save This Manual You will need the manual for the safety warn

19. Store idle tools out of reach of children and other untrained persons. Tools are dangerous in the hands of untrained users. Never allow children to come in contact with this product. 20. Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained tools with a sharp cutting edge are less likely to bind and are easier to control. Do not use a damaged tool. Tag damaged tools “Do not use” until repaired. 21. Check for misalignment or binding of moving parts, breakage of par

Always release any built-up air even after disconnecting hose. Disconnect the Nailer when not in use. 11. Remove adjusting keys and wrenches. Check that keys and adjusting wrenches are removed from the tool or machine work surface before attaching to an air source. 12. Avoid unintentional starting. Be sure the trigger is in the Off position when not in use and before plugging in. Do not carry any tool with your finger on the trigger, whether it is attached to an air source or not. Do not point t

Testing the Double Trigger Safety Mechanism Warning: Even though the nailer should be empty during this procedure, ALWAYS point the nailer at a piece of scrap wood when testing. 1. Make sure the tool is disconnected from the power supply. 2. Completely empty the magazine of nails. 3. The Nailer should not fire if the second trigger Safety Trigger (123) Trigger (125) Figure 1 is not pulled. 4. Check that the Trigger (125) and the Safety Trigger (123) move freely, without sticking see Figure 1. 5.

Squeeze the Trigger (39). The tool should not cycle (fire). If it cycles (fires), stop immediately and take the tool to a qualified service technician. 8. Depress the Safety (52) against the workpiece and squeeze the Trigger (39). The tool must cycle (fire) once only. Release the trigger and squeeze it again. The tool must cycle (fire) once only. REV 10a With the Trigger held, carefully lift the nailer and press it against the workpiece again. The tool must not cycle (fire). If it fails to act i

ASSEMBLY AND OPERATING INSTRUCTIONS NOTE: For additional information regarding the parts listed in the following pages, refer to the Assembly Diagram on page 14. Apply Pressure Here Power Cord (7) Safety (21) Nose (19) Trigger (13) Magazine (22) Lever (29) Fastener Window FIGURE 1 Warning: This Nailer / Stapler is not suited for nailing or stapling into concrete, masonry, bricks, or metal. Warning! Do not fire if Brad Nails or Staples are jammed in the Nose (19) section. Unplug the unit and foll

It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death. Indicates a hazardous situation which, if not avoided, will result in death or serious injury. Indicates a hazardous situation which, if not avoided, could result in death or serious injury. Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury. Addresses practices not related to personal injury. Symbol Propert

e. Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enables better control of the tool in unexpected situations. f. Use safety equipment. A dust mask, non-skid safety shoes and a hard hat must be used for the applicable conditions. Wear heavy-duty work gloves during use. Wear a full face shield if you are producing metal filings or wood chips. g. Always wear eye protection. Wear ANSI-approved safety goggles with side shields during use. h. Always wear he