Mower not level side to side, uncut or partially cut grass. 2. Blades dull or bent. 3.Carrier RPM too low. 4. Field conditions are so wet that the tractor tire is pushing grass into mud. 5. Ground speed too fast. 6. Blades lock back. 7. Blades riding up due to blade bolt wear or loose bolts. 8. Grass is down from previous weather conditions, 9. Possible build up of marerial under mower. Level 3 pt. Hitch linkage on tractor. Sharpen or replace blades. Use correct PTO speed. Too wet to

Replace any missing or illegible safety decals. Inspect for any damaged or worn parts and replace before next use. Store the Rough Cut Mower in a dry environment. 16 MAINTENANCE 1. Periodically check and maintain proper gear oil level. 2. Approximately every 8 hours, grease spindles (3), roller axle (1), wheel forks (4), wheel axles (4), PTO shaft universal joints (2), and PTO telescoping surface. NOTE: Use a high-temp/multi-purpose grease. 3. Before each use check to make sure all safety

Do not allow anyone to operate or assemble this equipment until they have read this manual and have developed a thorough understanding of the safety precautions and operation. Review safety instructions with all users annually. • This equipment is dangerous to children and anyone unfamiliar with its operation. The operator should be a responsible, properly qualified and physically able person familiar with farm machinery and competent in this equipment’s operation. • Never exceed the limits o

I Tighten and re-test. | Consult with an authorized servicing dealer. Refill with fresh, clean unleaded gasoline with a pump octane of 87 or higher mixed with 50:1 Shindaiwa Premium 2-cycle mixing oil or with an equivalent high quality 2-cycle mixing oil. I Replace fuel filter or vent as required. Restart. I Move switch to “I” (ON) position and restart. Consult with an authorized servicing dealer. I Crank the engine with the plug removed, reinstall | the plug, and restart. Clean and regap

Always mix all fuels in a clean approved container. 1. Place the unit on a flat, level surface, and wipe any debris from around the fuel cap. 2. Remove the fuel cap. 3. Fill the tank with clean, fresh fuel. 4. Replace the cap, and wipe away any spilled fuel before starting the engine. 11 Starting the Engine 4. While holding the outer tube firmly Engine ignition is controlled by a two with one hand, slowly pull the recoil position switch mounted on the throttle starter handle until resis

FR_1 SHINDAIWA OWNER’S/OPERATOR’S MANUAL P231 POLE PRUNER Minimize the risk of injury to yourself and others! Read this manual and familiarize yourself with the contents. Always wear eye and hearing protection when operating this unit.WARNING! Part Number 62891-94311 Rev. 3/08 Introduction Attention Statements The Shindaiwa P231 Pole Pruner is designed and built to deliver superior performance and reliability without compromise to quality, comfort, safety or durability. Shindaiwa’s high- perform

SRM-225U S/N: S79111001001 - S79111999999 Engine Cover, Starter......................................................................................................................................................4 Fuel System S/N: S79111001001 - S79111002122........................................................................................................6 Fuel System S/N: S79111005496 - S79111999999...........................................................................................

Immediately notify your retailer or ECHO Dealer of damaged or missing parts. Use the contents list to check for missing parts. CONTENTS Contents List items MODELS 2400/ 24001E 2410/ 24101E 1 - Power Head V V 1 • Drive Shaft Assembly V V 1 - PlasticBag (co-pack) V >/ -1, Operator's Manual V V -1, Safety Manual V V -1, Warranty Registration Card V V • 1, Limited Warranty Statement V V -1, Plastic shield V V -1,Tool Bag V V -1, 8mm x 10mm wrench V V -1, scrench V V -1, locking t

If your unit does not have a clamp, follow these directions. Tools Required: Screwdriver, 8mm x 10mm Open End Wrench. Parts Required: Clamp, 4mm x 18mm Hexagon Head, Bolt, Link. 6. Remove shield and gear housing as an assembly. a. Loosen two (2) screws that clamp the gear housing to the drive shaft housing. b. Remove locating screw found at the top of the gear housing. Pull shield and gear housing assembly from the drive shaft assembly. IMPORTANT Prevent flexible drive cable from sliding f

Store unit in a dry, dust free place, out of the reach of children. DANGER Do not store in enclosure where fuel fumes may accumulate or reach an open flame or spark or serious personal injury may result. 2. Place the stop switch in the "OFF" position. 3. Remove accumulation of grease, oil, dirt and debris from exterior of unit. IMPORTANT Some tree sap and resins are corrosive. Thoroughly wash the guide bar and sprocket areas after each use, then coat metal parts with light oil. 4. Perform all pe