Оценок - 2, средний балл: 3.5 ( )

Производитель: Echo Размер: 8.23 mb Название файла: 180250.pdf Язык инструкции:

Do not allow anyone to operate or assemble this equipment until they have read this manual and have developed a thorough understanding of the safety precautions and operation. Review safety instructions with all users annually. • This equipment is dangerous to children and anyone unfamiliar with its operation. The operator should be a responsible, properly qualified and physically able person familiar with farm machinery and competent in this equipment’s operation. • Never exceed the limits of a piece of machinery. If its ability to do a job, or to do so safely, is in question- DON’T TRY IT. • Use a tractor equipped with a Roll Over Protective System and seat belts. (ROPS) • Do not modify the equipment in any way. Unauthorized modifications could result in serious injury or death and may impair the function and shorten the life of the equipment. • In addition to the design of this implement, safety decals and safety equipment, accident prevention is dependent upon the awareness, common sense, forethought, and proper training of everyone involved in the operation, transport, maintenance, and storage of the machine. Also refer to safety messages and operating instructions in each of the appropriate sections of the tractor manual. Pay close attention to the safety decals affixed to the tractor and the Rough Cut Mower. 4 ROUGH CUT MOWER ASSEMBLY INSTRUCTIONS STEP 1 Place Rough Cut Mower on a flat, level surface. (See Figure 1) Figure 1 STEP 2 Remove the wired on PTO shaft, lift pins, and spacers. Loosen and remove the bolts four (4) on the lift arm brackets, that secure the lift arm support straps, lift arms, and lift arm braces from the shipping positions and set aside. (See Figure 2) STEP 3 Install the right lift arm and lift arm support strap using two (2) short bolt and one (1) lift pin. (See Figure 3) Note: The lift arm support strap has one hole punched larger than the other. The larger hole is to be used to fasten with the lift pin. Figure 3 5 ■% STEP 4 Loosen and remove the two (2) nuts and washers for the A-frame tailwheel section, leaving the bolts in place. (See Figure 4) Figure 4 STEP 5 Install both the right and left side lift arm braces by sliding them over the two (2) A-frame tailwheel bolts that were loosened in Step 4. Start the nuts on the bolts, but at this time DO NOT TIGHTEN THEM. Allow the lift arm braces to rotate forward and resi against the installed lift arm. (See Figure 5) Figure 5 6 STEP 6 Install the long top mounting bolt by inserting it through the hole in the left side lift arm brace, the lower of the two (2) holes in the left side lift arm, the spacer, the lower of the two (2) holes in the top of the right side lift arm (which should not be attached to the lift arm bracket at this time), and finally through the right side lift arm brace. Install a washer and start the nut on the bolt, but do not tighten it at this time. (See Figure 6 & 8) ’ Figure 6 Note: You may have to move the assembly around to start the nut & washer. If unable to get the nut and washer started a "C" clamp may be necessary to compress the assembly to be able to start the nut & washer. Figure 8 7 STEP 7 Using the right side lift arm as a lever, pull to the inside of the lift arm bracket and inset bolt through lift arm and lift arm bracket. Install washer and nut. Place the lift pin in the larger of the two (2) holes on the lift arm brace and loosely attach the lift arm. Finally insert bolt, nut and washer to lower section of lift arm support strap to lift arm bracket. (See Figure 10) Figure 10 STEP 8 Tighten all nuts and bolts. 8 BEFORE PUTTING ROUGH CUT MOWER INTO SERVICE IMPORTANT INSTRUCTIONS PRIOR TO OPERATING MOWER SHIPPED WITHOUT OIL IN GEAR BOX AND WITHOUT GREASE IN GREASE FITTINGS. UNIT MUST BE SERVICED BEFORE USING. • Fill Gearbox using Multi-Purpose Gear Oil. • For all Grease Fittings use a high-temp/multi-purpose grease. STEP 1 Place Rough Cut Mower so that the deck is secure and level. STEP 2 Remove 1/2” Pipe Plug (located at top of gearbox) and 1/8” Pipe Plug (located at lower 1/3 of gearbox.) STEP 3 Fill gearbox using multi-purpose gear oil through top 1/2” fill hole until gear oil is level with lower 1/8" hole. STEP 4 Replace both the 1/2” pipe plug (located at top of gear box) and 1/8" pipe plug (located at lower 1/3 of gear box) and clean off any excess oil. STEP 5 Grease the following zerts: *Tail wheel fork (See Figure 13, page 17). *Tail wheel fork (See Figure 14, page 17). *Both U-Joints on the PTO shaft (See Figure 14, page 17). STEP 6 Inspect all guards to insure they are in good working order. If not replace before using. STEP 7 Check all bolts, nuts and belt to insure they are tight and secure. CAUTION: DO NOT overfill gearbox. This could cause damage to oil seals and can cause permanent damage to the gearbox. This issue will not be covered under warranty. 9 A PREPARATION • Never operate the tractor and mower until you...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: