Оценок - 4, средний балл: 4
(
)
)
|
Фрагмент инструкции
If your unit does not have a clamp, follow these directions. Tools Required: Screwdriver, 8mm x 10mm Open End Wrench. Parts Required: Clamp, 4mm x 18mm Hexagon Head, Bolt, Link. 6. Remove shield and gear housing as an assembly. a. Loosen two (2) screws that clamp the gear housing to the drive shaft housing. b. Remove locating screw found at the top of the gear housing. Pull shield and gear housing assembly from the drive shaft assembly. IMPORTANT Prevent flexible drive cable from sliding from drive shaft housing. If cable does slide free, clean dirt from cable and re-lubricate with lithium based grease prior to re-assembly. ™ me ch a. 7. Remove front handle. a. Remove four (4) screws and nuts and handle support from handle. b. Remove handle. 8. Install clamp. NOTE Nylon line head operation uses type (A) clamp, blade operation uses type (B) clamp. a. Type (A) clamp installation. - Slightly spread clamp and slide up shaft. - Install hex head bolt, DO NOT tighten at this time. b. Type (B) clamp installation. - Slightly spread clamp and slide up shaft. - Install single link using spacer, DO NOT tighten at this time. 9. Re-install gear housing and shield and front handle. 10. Balance unit a. Put on harness and attach unit to harness. b. Slide clamp up or down until unit balances with head approximately 2" - 3" from the ground. c. Tighten clamp screw. THROTTLE CABLE AND IGNITION LEADS SRM-2400 (For SRM-2410, see U-Handle Installation). Tools Required8mm x 10mm open end wrench , 3mm Allen Wrench. 1. Close choke and remove air filter cover. 2. Loosen nut (A) and place threaded end of throttle cable in bracket slot. Finger tighten nut (A). 3. Place inner cable in slot of carburetor swivel (B) and tighten nut (A). 4. Check throttle action. Operate freely? Opens completely? Returns to idle? 5. Connect ignition leads (C), one connector terminal pair and one ring terminal which attaches under fan terminal screw. 6. Re-install air filter and cover. Grass Trimmer/Brush Cutter a y Operator's Manual • * LOOP HANDLE INSTALLATION Tools Required: Screwdriver. Parts Required: Loop Handle, Handle Support, Four (4) 5mm x 35mm screws with captivated washers, four (4) 5mm nuts. 1. Position loop handle on drive shaft, DO NOT tighten screws yet. 2. Position handle for comfortable operation and secure screws. U-HANDLE INSTALLATION Tools Required: 8mm x 10mm Open End Wrench, Screwdriver, 3mm Allen Wrench. Parts Required: U-Handle Kit. NOTE On model 2410 use Steps 1,11 through 16 only. 1. Close choke and remove air filter cover. 2. Disconnect ignition stop leads (C). 3. Remove inner throttle cable from carburetor swivel (B). 4. Loosen nut (A) and remove throttle cable bracket. maecm. 5. Loosen screws (D) and pull drive shaft assembly from clutch case. 6. Loosen four (4) rear handle screws and pull rear handle (E) from the drive shaft assembly. 7. Loosen screw and pull Hook Assembly (G) from drive shaft assembly. 8. Loosen four (4) screws and remove Loop Handle (H). 9. Position Handle Bracket (J) 15 3/4 inches (400mm) from engine end of drive shaft. Secure with two (2) 6mm x 30mm bolts. 10* Install Hook. Three loop hook for use with nylon line head, or single ring (included with Blade Conversion Kit) for blade use. Position 8 5/8 inch (220mm) from engine end of drive shaft assembly. DO NOT tighten at this time. 400 mm (15-3/4 in.) t 220 mm (8-21/32 in.) 11. Install handles in bracket, place clamp top over handles and secure with four (4) 5mm x 35mm bolts (K). Grass Trimmer/Brush Cutter a q Operator's Manual • & 12. Secure throttle cable and leads to drive shaft by sliding wedge under harness hook. 13. Install drive shaft and align gear box, power head and U-handles. Tighten all screws. 14. Place throttle cable in slot in bracket with one nut on each side of bracket. Finger tighten both nuts (A). 15. Attach inner cable to swivel (B). Check throttle for freedom of movement and that wide open throttle / low idle extremes are adjusted properly. If adjustment cannot be achieved with adjusting nuts, the outer cable must be adjusted by moving the Cable Adjustment Clamp (L). Consult with your Echo Dealer for correct adjustment procedure. 16. Attach ignition leads (C). 17. Balance unit. a. Put on harness and attach unit to harness. b. Slide clamp (M) up or down until unit balances with head approximately 2 - 3" from ground. c. Tighten clamp screw. 2omcHO\ Pre - Opération OPERATION WITH BLADES Ereparing the Trimmer/Brush Cutter for Blade Use WARNING £k DANGER Blade use DEMANDS specific Brush Cutter configuration. Operation without specified shield and harness can result in serious personal injury. Plastic and Nylon Blades Require "Blade Conversion Kit," P/N 99944200400 (metal shield [A] and shoulder harness [B]). |- Steel/Metal Blades Require "Blade Conversion Kit" PLUS a *U-Handle Kit” (C) P/N 35130449230. Choosing the Correct Blade WARNING A DANGER The type of B...
Эта инструкция также подходит к моделям:Садовые инструменты - SRM-2400 (1.49 mb)