1345315 ©Delta International Machinery Corp. 1993 ▲ ▲▲DELTA INSTRUCTION MANUAL TABLE OF CONTENTS SAFETY RULES..............................................................3 INTRODUCTION..............................................................3 UNPACKING.................................................................3 ASSEMBLY INSTRUCTIONS Assembling Cyclone Separator To Fan Housing................................4 Assembling Legs To Blower Assembly...............................

The smaller the gauge number, the heavier the cord. 15. SECURE THE WORKPIECE. Use clamps or a vise to hold the workpiece when practical. Loss of control of a workpiece can cause injury. 16. FEED THE WORKPIECE AGAINST THE DIRECTION OF THE ROTATION OF THE BLADE, CUTTER, OR ABRASIVE SURFACE. Feeding it from the other direction will cause the workpiece to be thrown out at high speed. 17. DON’T FORCE THE WORKPIECE ON THE MACHINE. Damage to the machine and/or injury may result. 18. DON’T OVERREACH. Lo

Water) Maximum Hose Velocity PPM Bag Area in Sq. Ft. dBA " Hose Size Drum Size 50-180 1 HP 1 Ph. 115/230 60-3450 700 4Vz" 5131 19.0 83. 5" x 60" 55 Gal. 50-181 2 HP 1 Ph. 230 60-3450 1100 8 W 5600 19.0 85 6" x 60" 55 Gal. 50-182 3 HP 3 Ph. 230/460 60-3480 ! 1300 10» 6619 50.0 84 6" x 60" 55 Gal. / - - ’ . ■' - ' • ■" DATED 11-28-94 " . - PART NO. 410-06-651-0001 © Delta International Machinery Corp. 1994 READ INSTRUCTIONS CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE, INSTALL, OPERATE OR SERVIC

Cutters 09-128 & 09-137 are counterbored to fit Stub Spindle. Cutters are shown 3/8 size. 1/2 Lb. each. 09-100 09-101 09-102 09-103 09-106 1/2" Cove 5/16" Cove 1/8" & 3/8" 1/4" & 1/2" 90° 5/16" Qr. Rd. 3/8" Bead Qr. Rd. Qr. Rd. V-Groove 1/4" Bead 09-109 09-111 09-112 09-113 09-114 1/4" Flute Stile with Rail with Drop Leaf Drop Leave 1/4" Groove 1/4" Tongue Bead Cove 09-115 09-116 09-117 09-118 3-Bead Clover 1/2" Rad. 3/4" Qr. Rd. Cove Leaf Base Shoe 09-120 09-121 09-125 09-126 09-128 Ogee Female

In a severe dirty operation, the blower impeller should be cleaned with a wire brush to prevent an accumulation of foreign matter that could result in blower unbalance After cleaning impeller, inspect for possible cracks or excessive wear, which can cause unbalance. DO NOT USE AN IMPELLER THAT IS CRACKED OR EXCESSIVELY WORN; REPLACE IT WITH A NEW IMPELLER. MOTOR MAINTENANCE: Removing dust and dirt: Blow off motor with low pressure air to remove dust or dirt. Air pressure above 50 P.S.I. shou

Fire resistant aluminum foil lined fiberdrum. 24* diameter x 31 "high. 14 lbs. No. 50-311 Drum DoUey. 5-wheel. Accommodates 55-gallon capacity fiber or metal drum. Adds portability to your dust collector system. No. 50-225 2' Diameter x 3f Dust Bag. 22 sq. ft. filter area. New 3-dimensional weave for improved dust retention. With drawstring to fit standard 55-gallon drum. For use with No. 50-1801 HPaod 50-181 2 HP Dust Collectors for planer chip pick up. Also No. 50-1801 HP Unit when major u

Current models have stamped sheet metal blower housings. D - When screw requires servicing install at 100 inch lbs 10 REPLACEMENT PARTS 50-185 BAG ASSEMBLY ----------- (OPTIONAL FOR 50-180 & 50-181 - STANDARD FOR 50-182) REF № PART NUMBER 50-185 1 50-188 2 410-06-027-00001 3 410-06-105-0001 4 50-195 OESCRIPTIQN DRUM MOUNTED DUST BAG, CONST OF: HOSE, INCL; CLAMP - 6" HOSE SLEEVE DUSTBAG NOT SHOWN ASSEMBLED NOTE: THE NECK OF THE BAG MUST BE CLAMPED TO THE DRUM USING A STANDARD 55

The fan should rotate clockwise. You can reverse the rotation of the motor by interchanging any two of the three incoming power lines connected to terminals (C) Fig. 16. Disconnect the machine from the power source before reversing the wires. ADANGER 460 VOLT OPERATION 460V operation of the 50-762 requires replacement of the motor starter and reconfiguration of the motor's internal connections. This item is available from most industrial electrical supply dealers and must be installed by a q

5 facing up, and attaching the legs in that position. NOTE: Before using the alternate set-up, remove the 5/16" hex head screws from holes (B) Fig. 6 in the motor/blower assembly and place them in the holes (C). Air will leak if the screws are left out of these holes. ATTACHING THE DUST INTAKE PORTS Disconnect the machine from the power source! AWARNING Place the dust intake port (A) Fig. 7 over the intake hole (B) opposite the motor. Align the four holes (C) (two of which are shown) in th

460 VOLT OPERATION 460 volt operation of the 50-764 requires replacement of the motor starter and reconfiguration of the motor's internal connections. A 460 volt starter is available from most industrial electrical supply dealers and must be installed by a qualified electrician. DO NOT ATTEMPT to wire the machine for 460 volts without replacing the starter. Doing so will cause damage to the machine and personal injury could result. FUNCTIONAL DESCRIPTION FOREWORD The Delta Industrial Models 50-7