Оценок - 4, средний балл: 5
(
)
)
|
Фрагмент инструкции
5 facing up, and attaching the legs in that position. NOTE: Before using the alternate set-up, remove the 5/16" hex head screws from holes (B) Fig. 6 in the motor/blower assembly and place them in the holes (C). Air will leak if the screws are left out of these holes. ATTACHING THE DUST INTAKE PORTS Disconnect the machine from the power source! AWARNING Place the dust intake port (A) Fig. 7 over the intake hole (B) opposite the motor. Align the four holes (C) (two of which are shown) in the port with the ones in the motor/ blower assembly (D). Fasten them with four M4 sheet metal screws. Turn the unit over so that the casters are on the ground. Because of the weight of the unit, use more than one person to place it into the upright position. ACAUTION 9 ATTACHING A DUST COLLECTION BAG Disconnect the machine from the power source! A. USING A CLOTH COVERED FLEXIBLE RING 1. Place the cloth-covered bag retainer ring (A) Fig. 8 inside the opening of the clear plastic dust collection bag. Fold about 6 inches of the bag around the retainer ring. 2. Place the bag in the large hole (B) Fig. 8 in the motor/blower assembly. Fit the retainer ring (A) Fig. 8 and (A) Fig. 9 into the bottom groove (B) Fig. 9. Bend and fold the ring to fit it into place. 3. Tug slightly on the bag to eliminate any slack and to make sure that the bag is secure and will not detach during collection. 4. Repeat for the other bag. B. USING A METAL BAG CLAMP You can also attach the plastic bag to the outside of the dust collector using the included clamp (B) Fig. 10: 1. Place the clamp (B) around the top of the plastic bag (A). Fold about 4 to 6 inches of plastic bag over the clamp (Fig. 10). 2. Place the clamp and plastic bag (A) Fig. 11 on the blower assembly. Fasten the clamp (B) securely. 3. Repeat for the other bag. ATTACHING THE TOP FILTER BAG Disconnect the machine from the power source! AWARNING AWARNING 1. Place a 5/16" flatwasher on a 5/16" hex head screw. 2. Position the bracket (A) on the dust collector (Fig. 12). 3. Insert a 5/16" hex head screw through a hole in the bracket, then thread it into the appropriate hole in the dust collector. 4. Thread the other two screws into the other holes and tighten all three screws securely with the 12mm wrench. 10 5. Insert the rod into the pocket on the filter bag (A) Fig. 13. 6. Insert the rod in the hole in the bracket (B). 7. Work the open end of the filter bag into the top groove of the dust collector drum until it is secure and sealed. Bend and fold, as necessary, the internal bag retainer ring to fit it into place. 8. Attach the other filter bag in the same manner. 13 ATTACHING THE ACCESSORY HOSE TO THE INTAKE PORT Disconnect the machine from the power source! Models 50-762/50-763 provide four 4" dust ports. NOTE: Place the intake cap rings (D) Fig. 14 on the ends of each dust intake port before attaching the hose. Loosely place a hose clamp (A) Fig. 14 around one end of the flexible hose (B). Attach the hose to the dust intake port (C). Tighten the hose clamp (A). Attach the remaining clamp to the other end of the flexible hose and to the woodworking machine. NOTE: Do not operate the dust collector with any of the holes in dust intake port (C) Fig. 14 uncovered. To cover a hole not being used by a hose, place the flat intake cap (E) on dust intake port as shown in Fig. 14. SINGLE- AND THREE-PHASE WIRING Use a qualified electrician to install this machine to ensure safe and proper wiring and product operation. DIsconnect power at source before wiring the machine. ADANGER AWARNING AWARNING MODEL 50-762 THREE PHASE INSTALLATION (230 VOLT OPERATION) Your dust collector must be permanently connected to the building's electrical system and grounded to meet code. 1. To connect the dust collector to a power system, remove the controller cover (A) Fig. 15. 2. Bring the three-phase power line through the access hole (B) Fig. 15 in the bottom of controller box. 11 3. Connect the three power lines to terminals (C) Fig. 16, and the green ground wire to ground screw (D). 4. After connecting the power cord to the machine, view the rotation of the blower fan to make certain that the rotation of the motor is in the proper direction. The fan should rotate clockwise. You can reverse the rotation of the motor by interchanging any two of the three incoming power lines connected to terminals (C) Fig. 16. Disconnect the machine from the power source before reversing the wires. ADANGER 460 VOLT OPERATION 460V operation of the 50-762 requires replacement of the motor starter and reconfiguration of the motor's internal connections. This item is available from most industrial electrical supply dealers and must be installed by a qualified electrician. ESZQHMH DO NOT ATTEMPT to wire the machine for 460 volts without replacing the starter. Doing so will cause damage to the machine and personal injury could result. AWARNING AWARNING AWARNING Re-install t...
Эта инструкция также подходит к моделям:Прочие инструменты - 50-762 (640.03 kb)