In California, the engine must be designed, built and equipped to meet the State’s stringent anti-smog standards. Elsewhere within the United States, new off-road, spark-ignition engines certified for model year 1997 and later, must meet similar standards set forth by the EPA. HFT must warrant the emission control system on your engine for the periods of time described below, provided there has been no abuse, neglect or improper maintenance of your engine. Your emission control system may includ

6123457 9. Connect the hoses as marked (Hose 1 to Connection 1, for example) the hoses will only reach the proper connections if attached in the proper orientation - See Figure E. Filling the Hydraulic Fluid Figure FHydraulic Oil Cap (20) 1. Remove the Hydraulic Oil Cap (20) and fill the tank with Hydraulic oil (not included) - See Figure F. Remove and retain the O-ring (21). To check the hydraulic oil level, 2. remove the Dipstick connected to the Hydraulic Oil Cap, wipe it clean, then dip it b

Setup - Before use: Read the EntiRE impORtant SaFEtY inFORmatiOn section at the beginning of this manual including all text under subheadings therein before set up or use of this product. Functions lock Button power Switch 1/8. Shank with Buffing Wheel Collar accessories note: Refer to Parts List and Diagram on page 11 for accessory illustrations. • Use the Diamond Burr Bits (4) to drill hard, brittle materials, such as tile. • Use the mounted Stones (5) for sharpening cutting tools, screwdriver

If any parts are missing or broken, please call Harbor Freight Tools at the number on the cover of this manual as soon as possible. Air Hammer (10) Hammer Head (3) Air Hose (12) Range Adjust Block (6) Switch Assembly (13) Regulator (11) Anvil (5) Adjustable Pole (7) Stopper Pin (9) Mounting Holes (Qty. 4) Screw (2) Installation Mounting “C” Frame 1. Select a workbench in the shop area able to support the weight of the Planishing Hammer, the metal being worked on, and the vibration of the planish

Plane dry, unwarped, clean boards only. Avoid planing boards that have knots; loose knots can jam the machine or become a projectile. Do not plane boards that have foreign objects (nails, staples, etc.) in them. Do not plane material:7. shorter than 15”, • narrower than 3/4”, • wider than 13”, • or thinner than 1/8”• Push the On/Off Lock switch down to 8. turn the Planer on. Allow the planer to come up to full speed before beginning a job. The planer has a maximum depth 9. cut of 3/32” per pass.

This will provide a safer work area, by keeping it uncluttered, and avoid the danger of tripping, or damaging the power cord. Remember to retighten the Bleed Screw (#14) when you are finished. Page 6 SKU # 40318 GroundING / Voltage Warning Common household current is 110-120 volts. As long as the outlet used with this tool is rated from 110-120V there will be no complications using it with household receptacles. Plug the tool into a 110-120V properly grounded outlet protected by a 30-Amp., dual

Install four ‘AA’ Batteries, making sure to follow the polarity marked in the Battery Compartment. 3. Replace the Battery Cover and turn Battery Cover Knob until Cover is secured into place. Mounting To Tripod (3) 1. If mounting the Laser Level with the Tripod (3), position the Tripod on a flat and level ground surface. Extend Tripod Legs to the desired height, using the Bull’s Eye Vial (15) located on the Tripod Head (4). See Figure 2, below. Figure 2 Tripod Head (4) Bull’s Eye Vial (15) Tripod

We shall in no event be liable for death, injuries to persons or property, or for incidental, contingent, special or consequential damages arising from the use of our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation of exclusion may not apply to you. This warranty is expressly in lieu of all other warranties, express or implied, including the warranties of merchantability and fitness. To take advantage of this warranty,

Failure to do so can result in serious injury. Save this manual. Copyright© 2008 by Harbor Freight Tools®. All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual product may differ slightly from the product described herein. Tools required for assembly and service may not be

Allow any spilled gas to evaporate before starting Engine. 7. Inflate tires to 60 PSI. 8. Remove Wheel Bearing Dust Proof Caps (15) and verify Bearings (19) are completely packed with bearing grease. If they are not greased, remove Bearings and completely pack with bearing grease. Replace Bearings and Wheel Bearing Covers. If you are not familiar with this procedure, have a qualified mechanic do it. Engine Controls Hydraulic Fluid Fill Tube Cap with Dip Stick Hydraulic Fluid Fill Tube Primer But