Войти:
Скачали: 2   Размер: 2 mb   Производитель: Bolens  
Категория: Прочие инструменты
@name

Slide coupling half into place while guiding three mounting bolts through holes in pump support bracket. 10. Secure with nuts and washers removed earlier. 12 11. Set .010 to .060 inch clearance between the nylon “spider” and the engine coupling half by sliding a matchbook cover between the nylon “spider” and the engine coupling half and moving pump coupling half as needed. Secure pump coupling half with set screw. See figure 16. NOTE: Make certain proper clearance is obtained before tighteni

Скачали: 10   Размер: 2 mb   Производитель: Bolens  
Категория: Прочие инструменты
@name

Extend and retract the wedge fully 10 to 12 complete cycles to remove trapped air in the system (system is “self-bleeding”). FIGURE 10. f. Refill the reservoir to within 1-1/2" to 2" from the top of the tank. Much of the original fluid has been drawn into the cylinder and hoses. Make certain to refill the reservoir, to prevent extreme damage to the hydraulic pump. Failure to refill the tank will void your warranty. 8 NOTE: Some fluid may overflow from the vent plug as the system builds heat

Скачали: 26   Размер: 2 mb   Производитель: Bolens  
Категория: Прочие инструменты
@name

Improper adjustment will cause stalling when splitter is under load, hard starting and higher fuel consumption. Refer to the separate engine manual packed with your log splitter for carburetor adjustment information. NOTE: A dirty air cleaner will cause engine to run rough. Be certain air cleaner is clean and attached to the carburetor before adjusting carburetor. Do not make unnecessary adjustments. Factory settings are satisfactory for most applications and conditions. MAINTENANCE Hex Bolt

Скачали: 4   Размер: 3 mb   Производитель: Bolens  
Категория: Прочие инструменты
@name

Excessive engine speeds are dangerous. 5. Never store outside without a waterproof cover. 3 Rain will cause rust on the inside of the cylinder. TOOLS REQUIRED: (1) Raw Hide or Plastic Hammer (1) 1-1/8" wrench or adjustable wrench (2) 1/2" wrenches (1) Standard screw driver (1) 3/4" wrench (1) 5/8" wrench OTHER MATERIALS NEEDED: (A) One gallon or regular grade gasoline (for engine) (B) 2-3/4 pints of SAE 30 or 10W oil (for engine) (C) 2-1/2 gallons of 10W 30 H.D. oil only (for Log Sp

Скачали: 2   Размер: 3 mb   Производитель: Bolens  
Категория: Прочие инструменты
@name

Be sure oil drains completely. Replace oil drain plug and refill with oil as directed on page 5 or engine nameplate. 2. Check oil every five (5) operating hours or each time equipment is used. Clean cylinder fins and underside of tank or housing thoroughly of all accumulated grass and debris. 4. Air Cleaner. (See figure 18.) a. Paper Type Element. Remove every 10 hours or oftener if under dusty conditions. Tap to remove loose dirt and/or blow from inside out with low pressure air. Replace i

Скачали: 4   Размер: 1 mb   Производитель: Bolens  
Категория: Прочие инструменты
@name

Check fluid level before each use. A. Block up front of log splitter so the beam is level. B. Remove the fluid check plug from the back of the log splitter. See figure 9. If fluid starts to come out of the hole, fluid level is correct. If it does not, replace the check plug loosely, ^ pull the cap off the breather tube, and add Dexron II automatic transmission fluid until fluid starts out of the hole when the plug is removed. C. Replace fluid check plug securely. Replace cap on the breather

Скачали: 11   Размер: 2 mb   Производитель: Bolens  
Категория: Прочие инструменты
@name

x 1.5" Lg. 717-0461 Pump with Woodruff Key (645) 10 710-0117 Hex Bolt 5/16-24 x 1.00" Lg. 49 712-0123 Hex Nut 5/16-24 Thd.* (Grade 5) 50 736-0119 L.-Wash. 5/16" I.D.* 11 738-0406 Return Stroke Stop Plunger 51 717-0462 Flexible Coupling 12 750-0428 Engagement Handle 52 710-0117 Hex Bolt 5/16-24 x 1.00" Lg.* 13 08118 Grip 53 13295 Coupling Support Brkt. Ass'y. 14 747-0355 Cylinder Support Rod (for 3-1/2" 54 710-0216 Hex Bolt 3/8-16 x .75" Lg. Dia.) (642) 55 736-0105 Belleville Wash. 3/

Скачали: 4   Размер: 2 mb   Производитель: Bolens  
Категория: Прочие инструменты
@name

See figure 13. Never stand next to the ram when operating. See figure 14. Always stand behind the ram. 9 FIGURE 13 FIGURE 14 MAINTENANCE i WARNING i Always stop engine and disconnect spark plug wire before performing any maintenance or adjustments. ENGINE OIL Change oil first two (2) hours of operation and check oil level every five (5) operating hours or each time equipment is used. Change oil every twenty-five (25) operating hours or sooner if equipment is operated in exiremely dusty

Скачали: 5   Размер: 1 mb   Производитель: Bolens  
Категория: Прочие инструменты
@name

This increases the haz ard of personal injury. The maximum engine sp?ed is preset by the manufacturer and is within s jfe-ty limits. 5. Do not alter your splitter in any manner such as attaching a rope or extension to the control lever or adding to the width or height of the wedge. Such alterations may cause your splitter to be unsafe. 6. Perform all recommended maintenance procedures before you use your splitter. 7. Do not service or repair your log splitter without disconnecting the spark p

Скачали: 3   Размер: 2 mb   Производитель: Bolens  
Категория: Прочие инструменты
@name

Leaks can be located by passing a piece of cardboard or wood over the suspected leak and look for discoloration. 8. Should it become necessary to loosen or remove any hydraulic fitting or line, be sure to relieve all pressure by shutting off the engine and moving the control handle back and forth several times. 9. Don't remove the cap from the hydraulic tank or reservoir while your log splitter is running. Hot oil under pressure could cause injury. 10. Never store outside without a waterproof





Категории