Войти:
Скачали: 2   Размер: 477 kb   Производитель: Campbell Hausfeld  
Категория: Прочие инструменты
@name

Description 1 1/4" x 1 1//4" Screw 2 1/4" Nut 3 Tool storage tray 4 Handle * Standard Hardware Item Part No. Qty. WL023500AV 1 HL006100AV 1 Tools Needed Assembly Instructions - 1. Assemble tool storage tray with handle as shown in the diagram. 2. Tighten bolts with a wrench and assembly handle to compressor as shown in the manual. © 2003 Campbell Hausfeld For parts, product & service information visit IN553400AV 7/03

Скачали: 1   Размер: 916 kb   Производитель: Campbell Hausfeld  
Категория: Прочие инструменты
@name@name@name

Wash hands after handling. GENEral SafETy This product is part of a high pressure system and the following safety precautions must be followed at all times along with any other existing safety rules 1. Read all manuals included with this product carefullyBe thoroughly familiar with the controls and the proper use of the equipment MANUAL 2 . Only persons well acquainted with these rules of safe operation should be allowed to use the air tool Do not exceed the maximum operating pressure of the air

Скачали: 0   Размер: 5 mb   Производитель: Campbell Hausfeld  
Категория: Прочие инструменты
@name@name@name

Do not use any type of reactive gases, including, but not limited to, oxygen and combustible gases, as a power source. Use filtered, lubricated, regulated compressed air only. Use of a reactive gas instead of compressed air may cause the tool to explode which will cause death or serious personal injury. Use only a pressure-regulated compressed air source to limit the air pressure supplied to the tool. The regulated pressure must not exceed 125 psi. If the regulator fails, the pressure delivered

Скачали: 2   Размер: 5 mb   Производитель: Campbell Hausfeld  
Категория: Прочие инструменты
@name@name@name

f. Always wear eye protection. g. Always wear hearing protection when using the tool. Prolonged exposure to high intensity noise is able to cause hearing loss. h. Do not attach the hose or tool to your body. Attach the hose to the structure to reduce the risk of loss of balance if the hose shifts. i. Always assume that the tool contains fasteners. Do not point the tool toward yourself or anyone whether it contains fasteners or not. j. Do not nail on top of another nail. This is able to cause the

Скачали: 4   Размер: 751 kb   Производитель: Campbell Hausfeld  
Категория: Прочие инструменты

Скачали: 0   Размер: 167 kb   Производитель: Campbell Hausfeld  
Категория: Прочие инструменты
@name

The general principles of operation are the same as the AVW1/4; please refer to the AVW1/4 manual supplied for general information. This document describes the differences between the AVW100 and the AVW1 and where to find further information on the use of the AVW100 with specific sensors. 1. Differences in Specification Physically the AVW100 is identical to the AVW1 but electronically it differs in that it uses active circuitry, including electronic filters and amplifiers to precondition the v

Скачали: 9   Размер: 449 kb   Производитель: Campbell Hausfeld  
Категория: Прочие инструменты
@name@name

Protejase Ud. y a los demas observando todas las reglas de seguridad. El no seguir las instrucciones podria resultar en heridas y/o danos a su propiedad. Guarde este manual como referencia. Rodillos para PintarBUILT TO LAST Funcionamiento No desconecte la boquilla para conectar el rodillo antes de haber liberado toda la presion y haber apagado la rociadora. PARA CONECTAR EL RODILLO 1. Quitele la boquilla a la pistola. 2. Coloquele la arandela al conector del rodillo. PRECAUCION Arandela Figura 1

Скачали: 10   Размер: 449 kb   Производитель: Campbell Hausfeld  
Категория: Прочие инструменты
@name@name

3. Comience a pintar y oprima el gatillo con frecuencia de modo que pueda pintar sin esforzarse. Mantenimiento 1. Quitele el perno y hale el forro para sacarlo. 2. Desmantele las piezas del rodillo y limpielas por separado. Cuando haya pintado con pinturas de latex, es preferible utilice agua caliente enjabonada. 3. Con la armazeon aeun conectada a la pistola introduzca el extremo del rodillo en un cubo los residuos de pintura (Vea la Figura 3). 4. Introduzca el sistema de succion de la con solv





Категории