Оценок - 3, средний балл: 5
(
)
)
|
Фрагмент инструкции
460 VOLT OPERATION 460 volt operation of the 50-764 requires replacement of the motor starter and reconfiguration of the motor's internal connections. A 460 volt starter is available from most industrial electrical supply dealers and must be installed by a qualified electrician. DO NOT ATTEMPT to wire the machine for 460 volts without replacing the starter. Doing so will cause damage to the machine and personal injury could result. FUNCTIONAL DESCRIPTION FOREWORD The Delta Industrial Models 50-764 and 50-765 are dust collectors that will connect to woodworking machines that accept a 5" diameter hose. The units each come with two 1 micron filter bags and four 6 mil plastic collection bags. The 50-764 has a three phase 230V/460V 5HP motor, while the 50-765 has a single phase 230V 5 HP motor. 6 CARTON CONTENTS CARTON CONTENTS 1 2 Fig. 1C 1. Motor and blower assembly 2. Stand 3. Dust intake port 3 4 5 6 7 8 9 10 11 Fig. 1D 4. Cloth-covered bag retainer ring (2) 5. One micron upper filter bag (2) 6. Six mil plastic lower bag (4) 7. Legs (2) 8. Bag retainer clamp (2) 9. Lower bag support pole (2) 10. Bag hanger assembly (2) 11. Upper bag support pole (2) 7 1213 20 14 15 16 1718 19 21 1213 20 14 15 16 1718 19 21 Fig. 1E 12. Caster (4) 13. Intake cap and ring (4) 14. Knob for attaching legs to blower/motor assembly (6) 15. 3/8” (9.5mm) Flat washer for knobs (6) 16. 5/16” (9mm) Small flat washers for casters (16) 17. M4 Sheet metal screw for dust intake port (4) 18. 5/16”x3/4” Hex head screw for attaching casters to base (16) 19. 5/16” (8mm) Hex nut (2) 20. 5/16” (8mm) x 11/4” Hex head screw for bag hanger assembly (2) 21. 5/16” (8mm) Large washers for bag hanger assembly (2) 22. 3/8” washer for bag hanger assembly (2) UNPACKING AND CLEANING Carefully unpack the machine and all loose items from the shipping container(s). Remove the rust-preventative oil from unpainted surfaces using a soft cloth moistened with mineral spirits, paint thinner or denatured alcohol. Do not use highly volatile solvents such as gasoline, naphtha, acetone or lacquer thinner for cleaning your machine. After cleaning, cover the unpainted surfaces with a good quality household floor paste wax. ASSEMBLY ASSEMBLY TOOLS REQUIRED Phillips head screwdriver 12 mm wrench ASSEMBLY TIME ESTIMATE Assembly for this machine takes approximately 1-2 hours. 8 FOR YOUR OWN SAFETY, DO NOT CONNECT THE MACHINE TO THE POWER SOURCE UNTIL THE MACHINE IS COMPLETELY ASSEMBLED AND YOU READ AND UNDERSTAND THE ENTIRE INSTRUCTION MANUAL. THIS MACHINE IS HEAVY. USE TWO OR MORE PEOPLE WHEN LIFTING. CASTERS 1. Turn stand (A) upside down, as shown in Fig 1F. 2. Align holes in caster assembly (B) with holes in plates on stand. Place small 5/16” flatwasher on a 5/16”x3/4” hex head screw. Insert screw through hole in caster assembly and thread into hole in stand. Repeat for all holes in all casters. 3. Tighten hardware by hand, then set with a 12mm wrench. LEGS TO MOTOR/BLOWER ASSEMBLY 1. Place motor/blower assembly with the motor down. (Fig. 2) 2. Place 3/8” (18 mm) flatwasher on knob (A) Fig. 2. 3. Align holes (B) on legs with holes (C) in the motor/ blower assembly. Legs should extend up. Insert knob through hole (B) in the legs and thread into hole (C) in the motor/blower assembly. Tighten knob securely. 4. Repeat steps for all knobs on both legs. ATTACHING STAND TO LEGS ON MOTOR/BLOWER ASSEMBLY NOTE: TWO PEOPLE ARE NEEDED FOR THIS STEP. Place all four stand posts (A) Fig. 3 into four legs (B) on motor/blower assembly. A B Fig. 1F Fig. 2 B A C Fig. 3 A B D CC 9 ALTERNATE SETUP The steps so far will assemble the unit with the motor on top and dust intake ports on bottom, as shown in Fig 4. This unit can be assembled with the intake port (A) Fig. 5 in the up position by following the steps in “LEGS TO MOTOR/BLOWER ASSEMBLY.” The exception is to place the motor/blower assembly on a flat surface with the motor (A) Fig. 6 facing up before attaching legs. NOTE: BEFORE DOING THE ALTERNATE SETUP, REMOVE 5/16” HEX HEAD SCREWS FROM HOLES (B) FIG. 6 IN MOTOR/BLOWER ASSEMBLY AND PLACE IN HOLES (C). AIR LEAKAGE WOULD OCCUR IF SCREWS ARE NOT PLACED IN HOLES (C). Fig. 4 A Fig. 5 ATTACHING DUST INTAKE PORTS A B C Fig. 6 DISCONNECT MACHINE FROM POWER SOURCE Place dust intake port (A) Fig. 7 over intake hole (B) opposite the motor. Align four holes (C) in the port with the ones in the motor/blower assembly and fasten with four M4 sheet metal screws. Turn unit over so casters are on the ground. BECAUSE OF THE WEIGHT OF THE UNIT, MORE THAN ONE PERSON SHOULD LIFT MOTOR/BLOWER ASSEMBLY INTO UPRIGHT POSITION. A B Fig. 7 C 10 ATTACHING DUST COLLECTION BAG DISCONNECT MACHINE FROM POWER SOURCE USING CLOTH COVERED FLEXIBLE RING: 1. Take cloth-covered bag retainer ring (A) Fig. 8 and place it inside opening of clear plastic dust collection bag. Fold about 6 inches of the bag down around the retainer ring. 2. Place bag up into the motor/blower assembly (B) Fig. 8 and fit retainer ring (A) Fig. 8 and (...
Эта инструкция также подходит к моделям:Прочие инструменты - 50-765 (1.13 mb)