1. Follow all operating and safety procedures attached to the charger. 2. Use only Bosch battery pack catalog numbers BAT043 12V, BAT045 12V, BAT040 14.4V, BAT025 18V, BAT026 18V, BAT030 24V, and BAT031 24V. 3. Do not wash the Flashlight with water nor keep in a damp location. If the Flashlight gets wet, dry it off as soon as possible. 4. The Flashlight is ruggedly constructed. It should, however, be handled with care. Do not disassemble or forcibly twist head beyond it’s stopping point. C B A D

To insert battery A, align battery and slide battery pack into tool until it locks into position. Do not force. Operation 1. To turn the Flashlight "ON", squeeze and release trigger switch C. To turn Flashlight "OFF", squeeze and release trigger switch C. 2. Your Flashlight has a swivel head that can be rotated to desired position. To change the position of the head, rotate counterclockwise until it stops. To return head to it’s original position, rotate the head clockwise until it stops. Replac

1. Rotate lens cap D counter clockwise and carefully remove lens cap D. 2. Remove bulb E from spring. 3. Reinstall replacement bulb E in spring. 4. Reinstall lens cap D and rotate clockwise to tighten. Note: One replacement bulb is provided, located inside head of the unit. WARNING! Do not position the lighted Flashlight head on or near flammable or combustible materials. The bulb gets hot during use. WARNING! Do not splash the lighted Flashlight bulb with liquids. Hot bulb may shatter when cool

1. Suivez toutes les consignes de fonctionnement et de securite fixees au chargeur. 2. Utilisez uniquement les blocs-piles Bosch numero de catalogue BAT043 12V, BAT045 12V, BAT040 14.4V, BAT025 18V, BAT026 18V, BAT030 24V et BAT031 24V. 3. Ne lavez pas le lampe torche a l'eau et ne le gardez pas a un endroit humide. Si le lampe torchele se mouille, sechez-le des que possible. 4. Le lampe torche a une construction robuste. Il doit, toutefois, etre manie avec soin. Ne demontez pas la tete et ne fo

All grease packed hammers require a short ELECTRONIC FEEDBACK CIRCUITRY period of time to warm up. Depending on the (EFC) room temperature, this time may vary from The internal electronic feedback system approximately 15 seconds (90°F) to 2 provides a "soft start", which will reduce the minutes (32°F). A new hammer requires a stresses that occur from a high torque start. break-in period before full performance is The system also helps to keep the pre-realized. This period may require up to 5 sel

Holding the work by hand or outlet. Keep cord away from heat, oil, sharp against your body is unstable and may lead to edges or moving parts. Replace damaged loss of control. cords immediately. Damaged cords increase the risk of electric shock. -2 BM 1619929522 12/02 12/10/02 3:43 PM Page 3 Do not force tool. Use the correct tool for your application. The correct tool will do the job better and safer at the rate for which it is designed. Do not use tool if switch does not turn it “ON” or “OFF”.

Retain instructions for future reference. 2. Heed Warnings - Adhere to all warnings on the unit and in the operating instructions. 3. Attachments - Attachments not recommended by the product manufacturer should not be used, as they may cause hazards. 4. Installation Cautions - Do not place this unit on an unstable stand, tripod, bracket, or mount. The unit may fall, causing serious injury to a person and serious damage to the unit. Use only manufacturer-recommended accessories, or those sold

Power use common sense when operating a tools create sparks which may ignite the dust power tool. Do not use tool while tired or or fumes. under the influence of drugs, alcohol, or Keep by-standers, children, and visitors medication. A moment of inattention while away while operating a power tool. operating power tools may result in serious Distractions can cause you to lose control. personal injury. Electrical Safety Dress properly. Do not wear loose clothing Double Insulated tools are equipped

2). NOTE: You may notice some “wobble” or “run out” of the bit when run in a no load condition. This is due to the quick change SDS tool holder assembly. However, once the bit has a load placed upon it, the bit automatically centers itself to produce an accurate hole. NOTE: The high efficiency available from the rotary hammers can only be obtained if sharp and undamaged accessories are used. The "cost" to maintain sharp and undamaged accessories is more than offset by the "time saved" in operati

Such preventive safety measures reduce the risk of starting the tool accidentally. FORWARD/REVERSING LEVER & TRIGGER LOCK -7- VENTILATION OPENINGS BATTERY PACK AUXILIARY HANDLE DUST SHIELD LOCKING SLEEVE DRILL/HAMMER DRILL SELECTION DIAL BUTTON DEPTH GAUGE VARIABLE SPEED TRIGGER SWITCH NOTE: For tool specifications refer to the nameplate on your tool. FIG. 1 BATTERY CHARGED CONDITION INDICATOR WING KNOB Model Number 11225VSR 11225VSRH Shank style SDS SDS Charge time 15 min. 22 min. 26 min. Batte