Page 2 10. Always check hardware and assembled parts after assembling. All connections should be tight and hardware tightened. 11. Caution: Avoid sharp edges during use and assembly. 12. Beware of operating the power tool in explosive atmospheres, such as in the presence of flammable liquids, gases, or sawdust. Electrical products create sparks which may ignite sawdust released from the Dust Collector, as well as other dust and fumes. 13. Carefully inspect the condition of the accessory before u

In California, the engine must be designed, built and equipped to meet the State’s stringent anti-smog standards. Elsewhere within the United States, new off-road, spark-ignition engines certified for model year 1997 and later, must meet similar standards set forth by the EPA. HFT must warrant the emission control system on your engine for the periods of time described below, provided there has been no abuse, neglect or improper maintenance of your engine. Your emission control system may includ

NOTE: The cleaning solution will depend on the type of paint being used. See specific cleaning instructions on page 9. 2. Remove the Spatter Shield (46) by pulling it off the Paint Roller assembly. Remove the Paint Roller (43) and Roller Spindle (44) from the Roller Arm (39). To do this, press down the lever on the Locking Tab (38), then pull the Paint Roller Assembly off the Roller Arm. 3. Further disassemble the Roller Assembly by placing your thumb into the opening in the Roller Bushing (42),

3. Insert the Battery into the charger by aligning the rib on the Battery with the groove in the charger. Press the Battery into place.The Red LED will illuminate indicating that a Battery is charging. 4. NOTE: During recharging, the Battery will become slightly warm to the touch. This is normal and not a cause for concern. Do not keep the Battery or charger in an environment of extreme heat or cold. They will work best at room temperature. 5. The Red LED will remain on for approximately 1 hour

1. Keep your work area clean and well lit. Cluttered and dark areas invite accidents. 2. Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust or fumes. 3. Keep bystanders, children, and visitors away while operating a splitter tool. Distractions can cause you to lose control. Protect others in the work area from debris such as chips and sparks. Provide barriers or shields as needed.

The Main Handle (91) can be pointed either right or left. There are symbols for a Hammer and Drill on the left side and a symbol for a Drill only on the right side. To drill only, set the Switching Knob (22) so that the picture of the Hammer and Drill are facing forward. Turn the Main Handle (91) so that it points to the right at the Drill symbol (See Figure 2). To Hammer Drill, set the Switching Knob (22) so that the Hammer and Drill are facing forward. Turn the Main Handle (91) so that it poin

Allow any spilled gas to evaporate before starting Engine. 7. Inflate tires to 60 PSI. 8. Remove Wheel Bearing Dust Proof Caps (15) and verify Bearings (19) are completely packed with bearing grease. If they are not greased, remove Bearings and completely pack with bearing grease. Replace Bearings and Wheel Bearing Covers. If you are not familiar with this procedure, have a qualified mechanic do it. Engine Controls Hydraulic Fluid Fill Tube Cap with Dip Stick Hydraulic Fluid Fill Tube Primer But

THANK YOU for choosing a HARBOR FREIGHT TOOLS product. For future reference, please complete the owner’s record below: Model______________ Serial No._____________ Purchase Date_______________ SAVE THE RECEIPT, WARRANTY AND THESE INSTRUCTIONS. It is important that you read the entire manual to become familiar with the unit BEFORE you begin assembly. Technical Specifications Materials: 25 gauge steel with steel latches and low carbon steel hardware and drawer handles. Overall Dimensions: 11-1/2” D

Arc Welding Safety Warnings and Precautions Warning:This product, when used for welding and similar applications, produces chemicals known to the State of California to cause cancer and birth defects (or other reproductive harm). California Health & Safety Code 25249.5, et seq. 1. Avoid electrical shock. Do not permit electrically live parts, cables, or electrodes to contact skin, clothing, or gloves. Protective clothing should be free of holes, dry, and ANSI approved. This unit draws enough cur

6123457 9. Connect the hoses as marked (Hose 1 to Connection 1, for example) the hoses will only reach the proper connections if attached in the proper orientation - See Figure E. Filling the Hydraulic Fluid Figure FHydraulic Oil Cap (20) 1. Remove the Hydraulic Oil Cap (20) and fill the tank with Hydraulic oil (not included) - See Figure F. Remove and retain the O-ring (21). To check the hydraulic oil level, 2. remove the Dipstick connected to the Hydraulic Oil Cap, wipe it clean, then dip it b