Current models have stamped sheet metal blower housings. D - When screw requires servicing install at 100 inch lbs 10 REPLACEMENT PARTS 50-185 BAG ASSEMBLY ----------- (OPTIONAL FOR 50-180 & 50-181 - STANDARD FOR 50-182) REF № PART NUMBER 50-185 1 50-188 2 410-06-027-00001 3 410-06-105-0001 4 50-195 OESCRIPTIQN DRUM MOUNTED DUST BAG, CONST OF: HOSE, INCL; CLAMP - 6" HOSE SLEEVE DUSTBAG NOT SHOWN ASSEMBLED NOTE: THE NECK OF THE BAG MUST BE CLAMPED TO THE DRUM USING A STANDARD 55

In a severe dirty operation, the blower impeller should be cleaned with a wire brush to prevent an accumulation of foreign matter that could result in blower unbalance After cleaning impeller, inspect for possible cracks or excessive wear, which can cause unbalance. DO NOT USE AN IMPELLER THAT IS CRACKED OR EXCESSIVELY WORN; REPLACE IT WITH A NEW IMPELLER. MOTOR MAINTENANCE: Removing dust and dirt: Blow off motor with low pressure air to remove dust or dirt. Air pressure above 50 P.S.I. shou

Fire resistant aluminum foil lined fiberdrum. 24* diameter x 31 "high. 14 lbs. No. 50-311 Drum DoUey. 5-wheel. Accommodates 55-gallon capacity fiber or metal drum. Adds portability to your dust collector system. No. 50-225 2' Diameter x 3f Dust Bag. 22 sq. ft. filter area. New 3-dimensional weave for improved dust retention. With drawstring to fit standard 55-gallon drum. For use with No. 50-1801 HPaod 50-181 2 HP Dust Collectors for planer chip pick up. Also No. 50-1801 HP Unit when major u

Water) Maximum Hose Velocity PPM Bag Area in Sq. Ft. dBA " Hose Size Drum Size 50-180 1 HP 1 Ph. 115/230 60-3450 700 4Vz" 5131 19.0 83. 5" x 60" 55 Gal. 50-181 2 HP 1 Ph. 230 60-3450 1100 8 W 5600 19.0 85 6" x 60" 55 Gal. 50-182 3 HP 3 Ph. 230/460 60-3480 ! 1300 10» 6619 50.0 84 6" x 60" 55 Gal. / - - ’ . ■' - ' • ■" DATED 11-28-94 " . - PART NO. 410-06-651-0001 © Delta International Machinery Corp. 1994 READ INSTRUCTIONS CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE, INSTALL, OPERATE OR SERVIC

Knowledge is safety 3. FOLLOW ALL WIRING CODES and recommended electrical connections to prevent electrical shock or electrocution. 4. DO NOT PULL THIS UNIT BY THE POWER CORD. Do not allow the power cord to come in contact with sharp instruments or edges, hot surfaces, or oil or grease. Do not place any weight on top of the power cord. A damaged power cord can cause electrical shock or electrocution. 5. SUPPORT THIS UNIT OR SECURELY CLAMP IT TO THE WORK SURFACE WHEN IT IS USED IN A PORTABLE APPL

The smaller the gauge number, the heavier the cord. 15. SECURE THE WORKPIECE. Use clamps or a vise to hold the workpiece when practical. Loss of control of a workpiece can cause injury. 16. FEED THE WORKPIECE AGAINST THE DIRECTION OF THE ROTATION OF THE BLADE, CUTTER, OR ABRASIVE SURFACE. Feeding it from the other direction will cause the workpiece to be thrown out at high speed. 17. DON’T FORCE THE WORKPIECE ON THE MACHINE. Damage to the machine and/or injury may result. 18. DON’T OVERREACH. Lo

1345315 ©Delta International Machinery Corp. 1993 ▲ ▲▲DELTA INSTRUCTION MANUAL TABLE OF CONTENTS SAFETY RULES..............................................................3 INTRODUCTION..............................................................3 UNPACKING.................................................................3 ASSEMBLY INSTRUCTIONS Assembling Cyclone Separator To Fan Housing................................4 Assembling Legs To Blower Assembly...............................

Main Street 714-641-0529 Fax: 714-641-2947 Santa Barbara 93101 Buena Tool Co. 433 Laguna Street 805-963-3885 Santa Rosa 95401 Acme Electric Tool Repair 742 Wilson Street 707-546-5862 Santa Rosa 95403 H & V Tool Repair 1808 Empire Industrial Court #D 707-528-1111 Simi Valley 93065 Simi Tool Repair 1236 Los Angeles Avenue, UnHD 805-584-8138 Temecula 92390-5623 California Electric Service 41715 Enterprise Circle North 909-695-5445 Torrence 90502 Universal Tool Service 21804 S. Vermo

When using an extension cord, be sure to use one heavy enough to carry the current of the machine. An undersized cord will cause a drop in line voltage, resulting in loss of power and overheating. Fig. D-1 shows the correct gauge to use depending on the cord length. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord. MINIMUM GAUGE EXTENSION CORD RECOMMENDED SIZES FOR USE WITH STATIONARY ELECTRIC MACHINES Ampere Rating Volts Total Length of Cord in Feet Ga

Cutters 09-128 & 09-137 are counterbored to fit Stub Spindle. Cutters are shown 3/8 size. 1/2 Lb. each. 09-100 09-101 09-102 09-103 09-106 1/2" Cove 5/16" Cove 1/8" & 3/8" 1/4" & 1/2" 90° 5/16" Qr. Rd. 3/8" Bead Qr. Rd. Qr. Rd. V-Groove 1/4" Bead 09-109 09-111 09-112 09-113 09-114 1/4" Flute Stile with Rail with Drop Leaf Drop Leave 1/4" Groove 1/4" Tongue Bead Cove 09-115 09-116 09-117 09-118 3-Bead Clover 1/2" Rad. 3/4" Qr. Rd. Cove Leaf Base Shoe 09-120 09-121 09-125 09-126 09-128 Ogee Female