1) WARNING: Never modify the power tool or any part of it. Damage or personal injury could result. A. Variable speed trigger switch B. Lock-on button C. Forward/reverse button D. Chuck E. Cord protector with key holder F. Cord set G. Main handle A B D E DWD010 F G DWD014 A B D E F G FIG. 1 C SHOWN IN FORWARD POSITION A C A English English INTENDED USE These heavy-duty V.S.R. drills are designed for professional drilling. DO NOT use under wet conditions or in presence of flammable liquids or gase

Work that is apt to splinter should be backed up with a block of wood. Keyed Chuck (Fig. 1, 3, 4) The DWD010 and the DWD014 feature a keyed chuck (d). FIG. 3 FIG. 4 TO INSERT A DRILL BIT OR OTHER ACCESSORY 1. Open the chuck jaws by turning collar by hand and insert the shank of the bit about 19 mm (3/4") into chuck. Tighten the chuck collar by hand. 2. Place chuck key in each of the three holes, and tighten in clockwise direction. It’s important to tighten chuck with all three holes. To release

4. For masonry, use carbide-tipped bits or masonry bits. A smooth even flow of dust indicates the proper drilling rate. Chipping and Chiselling 1. To switch from hammer drilling to chiselling, first insert the SDS- plus® chisel and check if it is properly locked. 2. When switching from hammer drilling mode to chiselling mode, turn the chisel to the desired position. If you find resistance during mode change, turn the chisel slightly to engage the spindle lock. Depth Rod (Fig. 4) TO ADJUST THE DE

6 CARTON CONTENTS 1 2 Fig. 1 1. Motor and blower assembly 2. Stand 3 4 5 6 7 8 9 Fig. 1A 3. Dust intake port 4. Cloth-covered bag retainer ring (2) 5. One micron upper filter bag (2) 6. Six mil plastic lower bag (4) 7. Legs (2) 8. Bag retainer clamp (2) 9. Bag hanging rod (2) 7 1011 12 13 14 15 1617 1011 12 13 14 15 1617 Fig. 1B 10. Caster (4) 11. Intake cap and ring (3) 12. Bracket for bag hanging rod (2) 13. Knob for attaching legs to blower/motor assembly (4) 14. 3/8” (9.5mm) Lockwasher for a

RELEASE TRIGGER IMMEDIATELY, remove drill bit from work, and determine cause of stalling. DO NOT CLICK TRIGGER OFF AND ON IN AN ATTEMPT TO START A STALLED DRILL – THIS CAN DAMAGE THE DRILL. 5. To minimize stalling or breaking through the material, reduce pressure on drill and ease the bit through the last fractional part of the hole. 6. Keep the motor running when pulling the bit back out of a drilled hole. This will help prevent jamming. 7. With variable speed drills there is no need to center

To stop the tool in continuous operation, quickly press and release the trigger switch. Reversing Lever (Fig. 1) The reversing lever (H) is used to reverse the rotary hammer for backing out fasteners or jammed bits in drill-only mode. CAUTION: When reversing to clear jammed bits, be ready for strong reactive torque. To reverse the rotary hammer, turn it off and align the reversing lever (H) with the yellow arrow pointing backward (viewed when holding drill in operating position). To position the

WARNING: Use of this tool can generate and/or disburse dust, which may cause serious and permanent respiratory or other injury. Always use NIOSH/OSHA approved respiratory protection appropriate for the dust exposure. Direct particles away from face and body. WARNING: Always use eye protection. All users and bystanders must wear eye protection that conforms to ANSI Z87.1. WARNING: Always wear proper personal hearing protection that conforms to ANSI S12.6 (S3.19) during use. Under some conditions

Use only 3-wire extension cords that have 3-prong grounding type plugs and matching 3-conductor receptacles that accept the machine’s plug, as shown in Fig. A. Repair or replace damaged or worn cord immediately. 2. Grounded, cord-connected machines intended for use on a supply circuit having a nominal rating less than 150 volts: If the machine is intended for use on a circuit that has an outlet that looks like the one illustrated in Fig. A, the machine will have a grounding plug that looks like

1342493 'Delta International Machinery Corp. 1999 INSTRUCTION MANUAL TABLE OF CONTENTS SAFETYRULES. ................................................................................................................................3 IMPORTANTSAFETYRULESFORDUSTCOLLECTORS. .............................................................4 INTRODUCTION. ................................................................................................................................4 UNPACKING.. ............

ADVERTENCIA: LEASE ESTE INSTRUCTIVO ANTES DE USAR MANUAL DE INSTRUCCIONES EL PRODUCTO. MANUAL DE INSTRUCOES INSTRUCOES DE OPERACAO, CENTRO DE SERVICOS E CERTIFICADO DE GARANTIA. ADVERTENCIA: LEIA ESTAS INSTRUCOES ANTES DE UTILIZAR O PRODUTO. D25501 1-9/16" (40 mm) SDS Max ® Hammers / Martillo de 1-9/16" (40 mm) SDS Max ® / Martelo 1-9/16" (40mm) SDS Max ® D25601 1-3/4" (45 mm) SDS Max ® Demolition Hammer / Martillo Demoledor de 1-3/4" (45 mm) SDS Max ® / Martelo Demolidor 1-3/4" (45 mm) SDS Max