Оценок - 5, средний балл: 4.4
(
)
)
|
Фрагмент инструкции
Such preventive safety measures reduce the risk of starting the tool accidentally. FORWARD/REVERSING LEVER & TRIGGER LOCK -7- VENTILATION OPENINGS BATTERY PACK AUXILIARY HANDLE DUST SHIELD LOCKING SLEEVE DRILL/HAMMER DRILL SELECTION DIAL BUTTON DEPTH GAUGE VARIABLE SPEED TRIGGER SWITCH NOTE: For tool specifications refer to the nameplate on your tool. FIG. 1 BATTERY CHARGED CONDITION INDICATOR WING KNOB Model Number 11225VSR 11225VSRH Shank style SDS SDS Charge time 15 min. 22 min. 26 min. Battery Capacities 1.7Ah BAT019 2.5Ah BAT020 3.0Ah BAT021 Maximum Capacities: Material Concrete 3/4" 3/4" Steel 1/2" 1/2" Wood 3/4" 3/4" BM 1619929426 8/01 8/2/01 1:19 PM Page 8 Operating Instructions VARIABLE SPEED CONTROLLED TRIGGER SWITCH Your tool is equipped with a variable speed pressure to decrease speed. This accurate trigger switch. The tool speed can be speed control enables you to drill without controlled from the minimum to the center punching. It also permits you to use maximum nameplate RPM by the pressure as a power screwdriver. Bits are available for you apply to the trigger. Apply more driving screws as well as running bolts and pressure to increase the speed and release nuts. FORWARD/REVERSING LEVER & TRIGGER LOCK Your tool is equipped with a forward/ reverse rotation move the lever to the far reversing lever and trigger lock located right. To activate trigger lock move lever to above the trigger (Fig. 1). This lever was the center off position. designed for changing rotation of the chuck, ! CAUTION Do not change direction of and for locking the trigger in an “OFF” rotation until the tool comes position to help prevent accidental starts to a complete stop. Shifting during rotation and accidental battery discharge. For of the chuck can cause damage to the tool. forward rotation, (with chuck pointed away from you) move the lever to the far left. For SLIP CLUTCH The tool has an internal preset clutch. The counterclockwise. As clutch is slipping, the clutch is set such that sufficient force is bit will most likely stop rotating. When the transmitted to the bit for most drilling binding force on the bit is removed the conditions but it will slip when bit binds in clutch automatically resets. If you the hole or the tool is overloaded. Be aware experience bit binding and clutch begins to that due to required clutch setting, you may slip, immediately turn the tool "OFF" and experience a torque reaction an instant correct the condition leading to the bit before the clutch slips. This torque reaction binding. will twist the body of the rotohammer in the opposite direction as the bit rotates, i.e., AUXILIARY HANDLE Setting depth: After the auxiliary handle is The tool should be supported with the installed, slide the depth gauge to desired auxiliary handle, which can be swiveled 360°. depth and securely tighten wing knob. To swivel the handle loosen the hand grip, BRAKE move the handle to desired position, and When the trigger is released it activates the securely retighten the hand grip. electrical brake to stop the chuck quickly. DEPTH GAUGE This is especially useful in the repetitive Your drilling depth can be pre-set and/or driving and removal of screws. repeated by using the depth gauge. -8 BM 1619929426 8/01 8/2/01 1:19 PM Page 9 DRILL/HAMMER DRILL SELECTION DIAL The selector dial allows the tool to be set for various drilling applications. Shift the dial ! CAUTION Drill only action: For drilling right or left depending on the below in woods, metals, plastics or applications. other non concrete materials. Do not operate the selection dial until the tool come to a complete stop. Shifting during Drill with hammer action: For rotation of the chuck can cause damage to drilling in concrete, asphalt, the tool. tile or other similar hard materials. Do not use demolition or chipping bits such as bull points, chisels, spades, gouges, etc. BATTERY CHARGED CONDITION INDICATOR The battery is equipped with a charged To maintain the indicator accuracy, condition indicator. This indicator shows the occasionally discharge the battery until the charged condition of the battery during the speed of the machine is distinctly reduced working process. and the charged condition indicator goes off completely. BUTTON By pressing the button ON, the charged condition can also be checked when the battery is removed or when the machine is not in use. After approx. 4 seconds, the charged indicator switches off automatically. When the last indicating element blinks (0 10%), the battery is nearly discharged and must be recharged. Charged Condition 0 - 10% (Battery discharged) 10 - 20% 20 - 40% 40 - 60% 60 - 80% 80 - 100% (Battery charged) INSTALLING ACCESSORIES ! WARNING Disconnect battery pack Insert accessory into the tool holder through from tool or place the the dust shield, while twisting and pushing switch in the locked or off position before inward until it locks automatically into place. making any assembly, adjustments or Pull outw...