Запрещается пользоваться пылесосом без установленных фильтров. 23 CarVac_Bok1_26lang.indd 23 27 15:27:24 CarVac_Bok1_26lang.indd 24 Dansk Udpakning og samling Kontroller, at alle delene er med i kassen. Stovsugning 14. Slut Rapido til bilens 12 V-stromudtag. 15. En indikator (15a) lyser, nar Rapido er tilsluttet. 16. Tryk en gang pa startknappen (16a) for at starte/ stoppe Rapido. 17. S^t den fleksible slange i stovsugeren, sa det bliver nemt at na ind og stovsuge omrader, der ellers

If you need to lower the pres sure, it can be accomplished by these meth ods. 1. Back away from the sur face to be cleaned. The further away you are, the less the pressure will be on the surface to be cleaned. 2. Change to the 40. nozzle -this nozzle delivers a less powerful stream of water and a wider spray pattern. DO NOT attempt to increase pump pressure. A higher pressure setting than the factory set pressure may damage pump. TO USE SPRAY WAND The nozzles for the spray wand are stored in the

PRODUCT DESCRIPTION Linear’s Xtended Range FM receivers and transmitters are designed for use in various wireless remote control applications. When the Model XR-16 receiver detects a signal from its companion transmitters, it will verify the digital code, activate the correct output channel, and trigger the remote device connected to the receiver. The XR-16 receiver has full supervision capabilities. If the “status” option for a channel is selected, the receiver expects hourly status signals fro

10-14 Maintenance ..........................................15 (Sticky Note comment cgatewoo 23.03.2007 20:30:56 Changes are located on page(s): 6,7,16,20 - ENG 25,26,35,39 - FR 44,46,54,58 - SP) Storage ..................................................16 Accessories ...........................................17 Repairs ...................................................17 Trouble Shooting Guide ..................18-19 Warranty.................................................20 Francais .......

21-39 Espanol ............................................ 40-60 IMPORTANT Please make certain that the person who is to use this equipment carefully reads and understands these instructions before operating. IMPORTANT Assurez-vous que toute personne qui utilisera cet equipement lise attentivement ces instructions avant de l’utiliser. IMPORTANTE Asegurese de que la persona que va a usar esta herramienta lea cuidadosamente y comprenda estas instrucciones antes de utilizarla. Part No. SAFETY GUIDE

4. Flush wand assembly backwards with water or compressed air. 5. If pressure is still too high, repeat steps 2-4. 4. CHECKING OIL: The pump is shipped with the correct amount of oil in it. This pump should never need any oil added or changed unless it develops a leak. A 30 weight non- detergent oil can be used in this pump (approximately 6 oz.). If pump is leaking oil take to an Authorized Service Center. HIGH PRESSURE HOSE: Damaged high pressure hoses can burst which can cause a potentially ha

NOTE: The pressure of the spray on the surface you are cleaning increases as you move the wand closer to the surface. To increase angle to a fan spray, turn counterclockwise To decrease angle to pencil point spray, turn clockwise 4.4 HIGH PRESSURE/TURBO SPRAY Do not move the nozzle to adjust pressure. The high pressure rotary nozzle position is intended for maximum cleaning effect. Keep the spray lance min. 6” to 8” away from the cleaning surface at all times. Rotary Spray USE OF CLEANING CHEMIC

A SMALL AMOUNT OF OIL LEAKAGE IS NORMAL. 5.4 WATER SCREEN The pressure washer is equipped with a water inlet screen to protect the pump. If the screen is not kept clean, the flow of water to the pressure washer will be restricted and the pump may be damaged. • To clean inner water screen, remove quick connect and remove the filter screen from the pump inlet. (see page 4, item 13) • Backflush screen to clean • Replace screen and quick connect immediately to prevent any foreign matter from enterin

3. Adjust the engine to a low speed until you see water exiting the water outlet. NOTE: This may take up to 3-5 minutes. Adjust the engine throttle back to full RPM. 4. Once the unit is primed, stop the engine and connect the high pressure discharge hose to the water outlet of the unit. NOTE: The trigger gun and dual lance assembly should already be connected to the high pressure discharge hose at this time. START-UP/COLD WATER OPERATION: 1. Refer to the "Safety Precautions" pgs. 4-7 before star

Developed to ensure Optimum Performance andProtection. IMPORTANT...Use Year Round! 341904 012011 Warning: This product contains lead, a chemical known to the State of California to cause birth defects or other reproductive harm. Wash your hands after handling this product. INTRODUCTION Congratulations on the purchase of your new John Deere hot water pressure washer featuring the patented Electro Magnetic Firing (EMF) System! You can be assured your John Deere hot water pressure washer was constr