(2) Thereafter, through the 10th year after the date the Fireplace is installed, if replacement parts are available, CFM Corporation will provide a replacement for any defective part without charge for the part itself. The consumer must pay for everything else other than the part. (3) Thereafter, through the 30th year after the date the Fireplace is installed, if replacement parts are available, CFM Corporation will provide a replacement for any defective part at a cost to the consumer of CFM Co

Never locate this appliance where it may fall into a bathtub or other water container. 10. Do not run cord under carpeting. Do not cover cord with throw rugs, runners or the like. Arrange cord away from traffic areas and where it will not be tripped over. 11. To disconnect this appliance, turn controls to the off position, then remove plug from outlet. 12. Connect to properly grounded outlets only. 13. This appliance, when installed must be electrically grounded in accordance with local codes, w

The vent terminal shall not terminate : • Within 3 ft. of a building mechanical air supply. • Less than 12 inches from a perpendicular wall. • In an area which is allocated to the occupancy. • Under a window that pivots open. In addition, in a structure with three walls and a roof , the following restrictions apply: a) The minimum distance between the two side walls must be 72". b) The roof must not exceed the walls more than 24". c) If both those conditions apply, the clearance shall be as foll

25.853(a) High temperature sealant milpack or stove cement of 550°F or higher could be used instead. The joints of The outer pipe (fresh air pipe) must be taped with 315°F or higher temperature metal adhesive tape or the use of high temperature milpack or stove cement would be applicable. When using the unitized 30°, 45° or 90° elbows, apply 1/4” bead of high temperature, 550°F or higher, sealant (milpack or stove cement) to the joint of the inner pipe (flue pipe) and the straight section as it

I/O I/O A 3 2 1 7 B 6 5 4 Fig. 10 HEF22 touchpad buttons. The fireplace features conveniently separate controls for flame effect and for heater control. This allows you to operate the unit in three (3) different modes: • As a full-featured fireplace - both flame effect and heater are on. This mode allows you to enjoy the look of the fire along with the heat output of a heater. I/O I/O 3 A B 6 5 4 2 1 7 8 Fig. 11 HEF26 and HEF33 touchpad buttons. (Button 8 does not apply to HEF22.) • As a visual

(Operating without glass frame in place could cause carbon monoxide (CO) to spill into the room.) CAUTION: Allow unit to cool completely if it has been in operation. Kit Contents: • Screen Door Assembly, left • Screen Door Assembly, right • Arch Frame • Installation Instructions Installation Instructions NOTE: Remove all plastic from packaging. 1. Remove existing top louvre from fireplace by lifting up and pulling out (Refer to top louvre instruction manual for details). 2. Hang arch f

Warning: always use an approved gas pipe. Never use a conventional 6-inch pipe alone. • Install the first 4-inch B-vent section or flexible aluminum chimney liner. • Fasten the optional 6-inch collar adapter to the stove with the two (2) screws supplied. • Install the sections of the conventional 6-inch pipe. Over the flexible liner. That you want to cover up. OPERATION INSTRUCTIONS Wall thermostat The optional wall thermostat will automatically keep your room at an even temperature. You need to

NOTE: All electric connections are to be made in accordance with CSA Standard C22.1-Canadian Electrical Code part 1 or with the National Electrical Code, ANSI/ NFPA 70 (latest edition) and/or in accordance with local codes. CAUTION: Should this blower require servicing, the power supply must be disconnected. M Black White G Firebox Acces- sory Junction Box Speed Control Switch 120 Volt Wall Electrical Box T229 Fig. 9 Blower wiring diagram. UVDR Series Unvented Gas Fireplaces Blower Installation

FOR YOUR SAFETY DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPORS AND LIQUIDS IN THE VICINITY OF THIS OR ANY OTHER APPLIANCE. PLEASE READ THIS MANUAL BEFORE INSTALLING AND USING APPLIANCE Installation and service must be performed by a qualified installer, service agency or the gas supplier. WHAT TO DO IF YOU SMELL GAS: • Do not try to light any appliance. • Do not touch any electric switch; • Do not use any phone in your building. • Immediately call your gas supplier from your neighbor’s p

Remove and discard the green wire. Reinstall the nut but do not tighten yet. 7. While standing on the right side of the unit, locate the power cord where it exits the cabinet. Using pliers, gently cut and remove the power cord. Dispose of the power cord. 8. Using a slotted screwdriver, remove the 7/8" (22 mm) diameter knockout from the right hand side of the cabinet above where the strain relief was located. 9. Route the electrical cable from the breaker/fuse panel through the 7/8" (22mm) diamet