Min inlet pressure : 5 11 in w.c. Max inlet pressure : 7 14 in w.c. Vent size : 4” Diam. listed gas liner Valve : Natural gas Propane White Rogers Robertshaw Model 36C03U TYPE 139 Model 7000 MVRLC Millivolt operated Millivolt operated SIT SIT Nova model Nova model Millivolt operated Millivolt operated Blower : Variable speed, 140 CFM Thermo-switch : 120° F “ON” 110° F “OFF” bi-metal type Efficiency : 74% heating Clearances to combustibles : mantel : 10” from top of face place side wall : 0” from

* The glass used on your fireplace is a high temperature ceramic 5 mm thick with a special coating for use with gaseous fuels. Do not replace it with any other material. CAUTION : Do not operate your fireplace without a glass or with a broken glass. BURNER REMOVAL AND INSTALLATION : REMOVAL : 1. Slide the burner to the left and pull toward you. 2. To gain access to the fan, also remove the firebox bottom plate. INSTALLATION : 1. Put the bottom plate back in place. 2. Put the burner assembly back

• Provide adequate accessibility clearances for servicing and proper operation. • Provide adequate clearances around air openings into the combustion chamber.. • This appliance has a built-in draft hood, so no additional external draft hood is required. • If installing in a factory built fireplace, you may remove the damper, glass doors, screen, screen holder, baffles, and smoke shelf provided that what you take out can be reinstalled. Also you must retain the pieces you have removed, in case so

If you are using a factory built chimney, it must comply with UL 103 or ULC S629 standards; therefore it must be a Type HT (2100°F). It is extremely important that it be installed according to the manufacturer's specifications. If you are using a masonry chimney, it is important that it be built in compliance with the specifications of the National Building Code. It must be lined with fire clay bricks, metal or clay tiles sealed together with fire cement. (Round flues are the most efficient). Th

The instructions pertaining to the installation of your wood stove comply with ULC-S627 and UL-1482 standards. Read this entire manual before you install and use your new stove. If this stove is not properly installed, a house fire may result. To reduce the risk of fire, follow the installation instructions. Failure to follow instructions may result in property damage, bodily injury, or even death. Consult your municipal building department or fire officials about restrictions and installations

Stove Pipe TYPICAL INSTALLATIONS FACTORY BUILT CHIMNEY: ROOF FLASHING18" CLEARANCEWALL SUPPORTWALL RADIATION SHIELDRAIN CAP Wall installation CEILING SUPPORTRADIATION SHIELD Vertical installation MASONRY CHIMNEY: Clay liner Thimble Clean out door FACTORY BUILT THIMBLE: BRICK THIMBLE: OUTSIDE COMBUSTION AIR Your DROLET stove is approved to be installed with an outside air intake which is necessary for a mobile home. This type of installation is also required in air tight houses and houses with ne

2. Slide the ash pan in position. Side Panels and Ash Lip Installation: 1. Start by fixing the front part of the decorative side in the two clips welded on the sides of the fire box. 2. Then, fix the back of the decorative side with two screws and washers supplied. Line up the decorative side parallel to the side of the appliance. 3. Clip the ash lip into position, centred just below the door. LEGS AND ASH PAN Ash Lip Installation : 1. Just clip the ash lip into position, centred just below the

A wood stove must never be installed in a hallway or near a staircase, since it may block the way in case of fire or fall to respect required clearances. FLOOR PROTECTOR Your wood stove should be placed on a non-combustible surface. The floor protector should be under the stove, eighteen inches beyond the front and eight inches beyond each side of the fuel loading and ash removal opening. If there is a horizontal section of chimney connector, the floor protector should go under it and two inches

The vent terminal shall not terminate : • Within 3 ft. of a building mechanical air supply. • Less than 12 inches from a perpendicular wall. • In an area which is allocated to the occupancy. • Under a window that pivots open. In addition, in a structure with three walls and a roof , the following restrictions apply: a) The minimum distance between the two side walls must be 72". b) The roof must not exceed the walls more than 24". c) If both those conditions apply, the clearance shall be as foll

Warning: always use an approved gas pipe. Never use a conventional 6-inch pipe alone. • Install the first 4-inch B-vent section or flexible aluminum chimney liner. • Fasten the optional 6-inch collar adapter to the stove with the two (2) screws supplied. • Install the sections of the conventional 6-inch pipe. Over the flexible liner. That you want to cover up. OPERATION INSTRUCTIONS Wall thermostat The optional wall thermostat will automatically keep your room at an even temperature. You need to