Wear a barbecue mitt and scrub the cooking grate with a damp cloth. If the grill is allowed to cool down, cleaning the grate will be easier if removed from the grill and cleaned with a mild detergent. Note: Allow the drip tray to cool before attempting to clean. Important: Do not leave the grill outside during inclement weather unless it is covered (cover sold separately). Rain water can collect inside of the grill, or in the drip tray if left uncovered. If the drip tray is not cleaned after use

33-B Set Collar Slip Collar Center Firebox Wall Small Gap here 33-B. Insert the Spit Rod into the Motor. Make sure the machined groove is toward the handle. • ....Place Slip Collar on Firebox Wall. Make sure the pointed tip of the Spit Rod stays in the Motor. • ....Push Set Collar against the Slip Collar, provide a small gap to allow the Spit Rod to freely turn. • ....Tighten the thumbscrews on the Set Collar and the Forks to hold in place. 3233-A Handle Set Collar Fork(x4) Long Spit Rod NOTE: M

Outdoor Use Only I IIM MMP PPO OOR RRT TTA AAN NNT TT Read this manual carefully before assembling, using or servicing this grill. Keep this manual for future reference. If you have questions about assembly, operation, servicing or repair of this grill, please call Coleman at 1-800-835-3278 or ®® TDD: 316-832-8707. In Canada call CERTIFIED 1-800-387-6161. Contents General Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 General Installation . .

Do not bend the hooks while inserting or removing the Fryer Grease Pan. Fryer Grease Pan Hooks 19Electrode Wire Fryer Panel Step15 • ....Assemble Front Fryer Heat Shield. 15-A Fryer Heat Shield Engage Tabs into Rectangle Holes Electrode Wire 15-A. Assemble Fryer Heat Shield. • ....NOTE: Place the Fryer Heat Shield between the Fryer Panel and the Flexible Fuel Hose. Do not pinch Electrode Wire. • ....Engage the two tabs on the Heat Shield downward into the rectangle holes. 15-B Fryer Heat Shield

NOTE: Use Coleman® 16.4 oz. disposable propane cylinders. The LP-gas supply cylinder to be used must be constructed and marked in accordance with the specifications for LP-gas cylinders of the U.S. Department of Transportation (DOT) or the National Standard of Canada, CAN/CSA B339, Cylinders, Spheres and Tubes for the Transportation of Dangerous Goods. Operation To Light CARBON MONOXIDE HAZARD .... For outdoor use only. .... Never use inside house, camper, tent, vehicle or other unventilated or

This manual should be read in conjunction with the labeling on the product. Safety precautions are essential when any mechanical or prop respect and caution demanded will reduce the possibilities of personal injury or property damage. The following symbols shown below are used extensively throughout these instructions. Always heed these precautions, as they are essential when using any mechanical or propane fueled equipment. DANGER DANGER indicates an imminently hazardous situation which, if not

Proof of gas seal between the connector and the cylinder before gas flow takes place. 2. A flow-limiting device designed to limit the flow of gas in the event of a regulator or hose failure. 3. The connection has a thermal shut-off which will stop the flow of gas if the connection reaches a certain temperature. CURRENT GAS CYLINDERS ARE ALSO EQUIPPED WITH AN OVERFILL PROTECTION DEVICE (O.P.D.) WHICH GREATLY REDUCES THE CHANCE OF ACCIDENTALLY OVERFILLING THE CYLINDER. SPECIAL NOTE CONCERNING L.P.

• Also try placing a pan of water above the lit burner side to help meat retain its juices. Replenish water as needed. 29 Cleaning the Venturi WARNING Spider’s nests or wasp’s mud inside the venturi may cause fire at valve. If a fire occurs, immediately turn off gas supply at L.P. cylinder valve (see representative illustration in Fig. 22). If your grill is set up for use with Natural Gas, turn off gas supply at the system manual shut off valve. Note: Spiders and small insects can spin webs and

19-C Quick Disconnect Coupling 27ATTACHED TO THE FUEL SOURCE. WARNING This procedure MUST be performed OUTDOORS only! Be sure L.P. cylinder valve is closed. Attach to Grill. Read and follow directions on the cylinder and fuel hose safety tags. CAUTION In the connection process, the grill side of the connection will seal on the back-check in the valve, resulting in a slight resistance. The connection requires about one-half to three- quarters additional turn to complete the connection. To disconn

4-B 4-B. Assemble one Door Magnet to the Base with two Screws (TN). Door Magnet TN (x2) Hardware shown actual size (TN) M6 x 15mm Screw (2) Qty. 11 .... Assemble two Spacers to the Top Panel. .... Assemble the Top Panel to the Grill Cart. 5-A 5-A. Assemble the two Spacers to the Top Panel with four Screws (TN). Hardware shown actual size TN (x4) Top Panel Step 5 (TN) M6 x 15mm Screw (11) Qty. Spacer (x2) (with flange up) 5-B 5-B. Assemble the Top Panel to the Grill Cart with seven Screws (TN). T