Оценок - 2, средний балл: 5
(
)
)
|
Фрагмент инструкции
33-B Set Collar Slip Collar Center Firebox Wall Small Gap here 33-B. Insert the Spit Rod into the Motor. Make sure the machined groove is toward the handle. • ....Place Slip Collar on Firebox Wall. Make sure the pointed tip of the Spit Rod stays in the Motor. • ....Push Set Collar against the Slip Collar, provide a small gap to allow the Spit Rod to freely turn. • ....Tighten the thumbscrews on the Set Collar and the Forks to hold in place. 3233-A Handle Set Collar Fork(x4) Long Spit Rod NOTE: Machined Groove Toward Handle Slip Collar 33-A. Loosely assemble the Rotisserie parts as shown in Figure 33-A. Do not tighten the thumbscrews until properly positioned in the grill. Step34 • ....Attach the Grill Cover. 33-C 33-C. If using the LONG SPIT ROD, the Rotisserie Handle may remain on the LONG SPIT ROD since it remains out- side the firebox. 34-A Door is open 34-A. Open the bottom door. Lay the Grill Cover on the ground in front of the Grill with the zipper on top. Attach the bottom edge to the grill base using snaps provided. 34-B Door is closed 34-B. Close the bottom door. The cover will not fit over the grill with the bottom door open. The closed door also helps secure the bottom edge of the cover. 34-C 34-D 34-C. Pull the cover over the 34-D. To store, roll the cover, grill and close the and place inside the zipper. lower compartment and close the door. 33 NOTE: Step 35 applies to you only if your grill is set up from the factory to use LP GAS. If your grill is set up from the factory to use NATURAL GAS, skip to Step 36. • ....Attach an LP Cylinder to the Grill. Step35 35-A Cylinder Support LP Cylinder 35-A. Set LP Cylinder in the Cylinder Support with the outlet valve facing toward the front of the grill. 35-B. Tighten the Cylinder Retainer Bolt against the bottom cylinder collar. Cylinder Retainer Bolt 35-C 35-C. Insert the TYPE 1 Nipple of the regulator into the cylin- der’s Fuel Valve Outlet as shown. Turn the regulator hand wheel clockwise to tighten. No tools are needed. The hand wheel will come to a complete stop when the connection is secure, and gas will not flow until a positive seal is achieved. For leak-check procedure, read and fol- low the steps identified on page 36. IMPORTANT! TO ENSURE PROPER GAS FLOW, BURNER CONTROL VALVES MUST BE “OFF” BEFORE OPENING THE GAS CYLINDER VALVE. WARNING:During assembly of grill and when attaching or replacing the L.P. gas cylinder, insure that the gas sup- ply hose is free of kinks and/or damage and is at least 3” away from hot surfaces such as the grill casting. Type 1 Nipple Fuel Valve Outlet 34 • .... NOTE: Step 36 applies to you only if your grill is set up from the factory to use NATURAL GAS. If your grill is set up from the factory to use LP GAS, skip back to Step 35. Step 36 PLACE THE RUBBER PLUG ONTO THE GAS SUPPLY LINE. THEN ATTACH THE SOCKET END OF THE QUICK DISCONNECT COUPLING ONTO THE GAS SUPPLY LINE. TIGHTEN WITH A WRENCH. LEAK TEST AT THE FUEL SOURCE CONNECTION WITH SOAP AND WATER. THE RUBBER PLUG IS USED TO PROTECT THE CONNEC• .... Attach a NATURAL GAS line to the grill. TOR WHEN THE HOSE CONNECTOR IS NOT INSERTED. YOUR NATURAL GAS COMPANY MUST INSTALL AND CONNECT THE GAS SUPPLY LINE TO THE GRILL. 36-A Quick Disconnect Coupling Rubber Plug 36-B Hose Connector Rubber Cap TO CONNECT AT THE FUEL SOURCE: PUSH BACK THE SLEEVE OF THE QUICK DISCONNECT COUPLING AND INSERT THE HOSE CON- NECTOR. RELEASE THE SLEEVE AND PUSH THE CONNECTOR INTO THE COUPLER UNTIL THE SLEEVE SNAPS FORWARD. TO DISCONNECT AT THE FUEL SOURCE: PUSH BACK THE SLEEVE AND PULL OUT THE CONNECTOR. THIS AUTOMATICALLY SHUTS OFF THE GAS. IMMEDIATELY PLACE THE RUBBER PLUG INTO THE QUICK DISCONNECT END.TURN OFF THE FUEL SOURCE SHUT-OFF VALVE IF APPLICABLE. WARNING:DURING ASSEMBLY OF GRILL AND WHEN CONNECTING OR DISCONNECTING THE HOSE FROM THE FUEL SUPPLY LINE, INSURE THAT THE GAS SUPPLY HOSE IS FREE OF KINKS AND/OR DAMAGE AND IS AT LEAST 3” AWAY FROM HOT SURFACES SUCH AS THE GRILL CASTING. CAUTION:MAKE SURE THE GAS CONTROL KNOBS ARE IN THE “OFF” POSITION BEFORE CONNECTING THE LOWER END OF THE HOSE TO THE FUEL SOURCE. 36-C Quick Disconnect Coupling 35 WARNING This procedure MUST be performed OUTDOORS only! Be sure L.P. cylinder valve is closed. Attach to Grill. Read and follow directions on the cylinder and fuel hose safety tags. CAUTION In the connection process, the grill side of the connection will seal on the back-check in the valve, resulting in a slight resistance. The connection requires about one-half to three-quarters additional turn to complete the connection. To disconnect, turn counterclockwise. Tighten by hand only. DO NOT use tools. Connecting Type 1 L.P. Gas Cylinders 15 WARNING This procedure MUST be performed OUTDOORS only! Be sure L.P. cylinder valve is closed. Attach to Grill. Read and follow directions on the cylinder and fuel hose safety tags. CAUTION In the connection process, the grill side of the connection will seal on the back-check in the valve, resulting in a slig...
Эта инструкция также подходит к моделям:Грили - 7700 LP Gas Series (7.01 mb)