If the burner does not ignite with the valve open, gas will continue to flow out of theburner and could accidently ignite with risk of injury. Turn controls and gas source or tank OFF when notin use. WARNINGMatch-Lighting sDo not lean over grill while lighting. 1. Turn all burner control valves. Open lid duringlighting. Turn on gas at LP cylinder. 2. Place lit match into match holder, then into side of grill bottom (as shown below). 3. Push in and turn IGNITION BURNER knob to PRE-HEAT. Be sure b

You may also have other rights which vary from state to state. In the state of California only, if refinishing or replacement of the product is not commercially practicable, the retailer selling this product or the Manufacturer will refund the purchaseprice paid for the product, less the amount directly attributable to use by the original consumer-purchaser prior todiscovery of the nonconformity. In addition, in the state of California only, you may take the product to the retail establishment s

However, the method of assembly remains the same. PARTS DIAGRAM PARTS DIAGRAM SEFQDBAJJIZLCKBBEEFFGGDDNOTKKUSSPPVVBGHJMPRSSSTTAAOOQQRRIIHHIIMMNNCCYVXUULLWWWTTXX ASSEMBLYASSEMBLY 1 Place bottom shelf upside down. Insert Bent U Pin into the caster mounting plate to lock it in place, shown A. Spin the caster clockwise into the threads on the bottom shelf until secure. Remove the Bent U Pin and repeat for remaining casters. Make sure the two locking casters are secured at the rear and the non-lockin

415.16155110 KSN No. 02619884-6 IMPORTANT: Fill out the product record information below. Serial Number Seeratinglabelongrillfor serialnumber. Date Purchased Forsupportandto registeryour grill,pleasevisit usat Ifyou havequestionsor need assistanceduringassembly, pleasecall 1-800-241-7548. Estimated assembly time: 35-40 minutes The following are trademarks registered by W.C. Bradley Co. in the U.S. Patent and Trademark Office: Caldera@; Charcoal2Go®; Char-Broil@; American Gourmet®; Bandera®; Brus

Make sure all burner valves are OFF. 2. Open cylinder valve and wait 5 seconds. 3. Follow lighting instructions. Temperature-Activated Shut-Off The large plastic nut on the regulator assembly is designed in coordination with a check valve in the cylinder valve to shut off the flow of gas when exposed to temperatures between 240-300.F. In the event of a fire or hose break, one of the safeguards will function to control or stop the flow of gas from the propane cylinder. Never attempt to use damage

. When using an extension cord, make sure it is not in contact with a hot or sharp surface. . Outdoor extension cords should be marked with the letters “W-A” and a tag stating “Suitable for use with outdoor appliances”. . Do not cut or remove the grounding prong from the rotisserie motor power cord. Do not let cord hang over any sharp edge or hot surface. NORMAL OPERATIONNORMAL OPERATION NORMAL OPERATION Do not expose to rain. To reduce the risk of electric shock, keep extension cord connecti

Department of Transportation (DOT) or for Canada, CAN/CSA-B339, cylinders, spheres and tubes for transportation of dangerous goods, Transport Canada (TC). See LP tank collar for marking. • LP tank valve must have: • Type 1 outlet compatible with regulator or grill. • Safety relief valve. • UL listed Overfill Protection Device (OPD). This OPD safety feature is identified by a unique triangular hand wheel. Use only LP tanks equipped with this type of valve. • LP tank must be arranged for vap

Total (5) connections. Connect the two wires [(a) and (b)] from switch wiring harness into the back of Electronic Ignition module. Total (2) connections, shown A. Note: Switch terminals are larger than electrode terminals and should only be installed in location shown as (a),(b). Release the cap and nut from electronic ignition module. Attach electronic ignition module to the cart right side panel with the nut, shown B. Insert AA battery into ignition module, negative (–) end first. Then put on

P. ush and hold ELECTRONIC IGNITION button until the burner Lighting instructions are continued on the next page 11 Ignitor Lighting (continued) 8. For grills equipped with ELECTRONIC IGNITION ateach burner: Repeat steps 4 through 6 to light each burner. 9. Once each burner has ignited, turn knobs to desired setting. WARNING Turn controls and gas source or tank OFF when not in use. CAUTION If ignition does NOT occur in 5 seconds, turn theburner controls OFF, wait 5 minutes and repeat the lightin

Attach left sideburner shelf using three 1/4-20x3/4” screws, 7mm lock washers, 7mm flat washers, 1/4” nuts, shown A. Attach rear of shelf using one 1/4-20x1.” screw, 7mm lock washer, and 7mm flat washer in lower hole, shown B. Attach front of shelf and fascia using one #8x3/8” self-tapping screw and large flat washer, shown C. Under main control panel, attach front of shelf and fascia using one 1/4-20x3/4” screw, 7mm lock washer, 7mm flat washer and 1/4” nut, shown D/E. Now you may fully tighten