Flames inside oven or smoke from vent. When the oven is first plugged in, or when the power supply to the oven has been interrupted, the display will flash. The oven cannot be programmed until the clock is set. Be sure electrical cord is securely connected into the electrical junction box. Cord/plug is not installed and/or connected. Cord is not supplied with oven. Contact Sears or another qualified servicer. Service wiring not complete. Contact Sears or another qualified servicer. Power outage.

Use the Convection Bake feature when cooking speed is desired. The oven can be programmed for Convection Bake at any temperature Air circulation of Convection Cooking between 325° F (163 ° C) to 550 ° F (288 ° C). Fig. 1 Convection baking uses a fan to circulate the oven's heat evenly and continuously within the oven (See Fig. 1).This improved heat distribution allows for even cooking and excellent results using multiple racks at the same time. Foods cooked on a single oven rack will generally c

The use of undersized utensils will expose a portion of the burner flame to direct contact and may result in ignition of clothing. Proper relationship of utensil to flame will also improve efficiency. • Know which knob controls each surface burner. Place a pan of food on the burner before turning it on, and turn the burner off before removing the pan. •Always turn knob to the full LITE position when igniting top burners. Visually check that burner has lit. Then adjust the flame so it does not ex

Stop time must be set for 2, 3, or 4 hours past the start time. Follow steps in "Stopping or Interrupting a Self-Clean Cycle" in the "Self Cleaning" section. Soil is not completely removed. Failure to clean bottom front, top of oven or door areas outside oven seal. These areas are not in the self-cleaning area, but get hot enough to burn on food residue. Clean these areas before starting the self-clean cycle. Burned-on residue may be cleaned with a stiff nylon brush and water or a nylon scrubber

4). If the beep was missed, a quick glance at the display with oven temperature Figure 3 showing in the oven display is a good way to check that the oven has already reached the preheat temperature. Once the oven has preheated, PLACE FOOD IN THE OVEN. The "BAKE" light wilt stay on. Press _ when baking is complete or to cancel the preheat Figure 4 feature. To change Preheat temperature while oven is preheating (example changing from 350 to 425°F): If it is necessary to change the preheat temperat

Once the surface controls have been set to the OFF positions and the clock has been set with the correct time of day, the surface controls should return to normal operation. If the surface controls do not funcfion and the "Er" message remains in any display after following these procedures, contact Sears Service for assistance. ESEC Lockout Feature ( --) The self-clean feature will not operate whenever a radiant surface element is ON. The ESEC feature will not operate during a self-clean cycle o

You can call anytime day or night, or schedule a service appointment online, Sears has over 12,000 professional repair specialists, who have access to over 4,5 million quality parts and accessories, That's the kind of professionalism you can count on to help prolong the life of your new purchase for years to come, Purchase your Master Protection Agreement today! Some liroitations and exclusions apply. For prices and additionaJ information call 1-800-827-6655, Sears Installation Service For Sears

Please note that not all cookware will fit the Bridge element correctly. 4. When cooking has completed, turn the surface control knob to OFF before removing the cookware. Note: The HE message will appear inthe display after turning the control knob to OFF if the cooktop is still hot and Figure 5 remain on until the heating surface area has cooled sufficiently. The message Front portion only may remain on even though the controls are turned OFF. Note: See Table on previous page for recommended co

3. Turn the knob to adjust the setting if needed. Start most cooking operations on a higher setting and then turn to a lower setting to finish cooking. Each surface element provides a constant amount of heat at each setting. A glowing red surface heating area extending beyond the bottom edge of the cookware indicates the cookware is too small. Please note that not all cookware will fit the Bridge element correctly. 4. When cooking has completed, turn the surface control knob to OFF before removi

If no pan is detected, no heat will be generated and the cooking zone wiii turn off after 3 minutes. 10 Setting Cooktop Controls Power Sharing In order to give you more flexibility, your induction cooktop is equipped with more cooking zones than the number of induction generators. Each of those generators is assigned to power a specific cooking zone (Fig. 25). One or two cooking zones are assigned to each generator. To be able to give you access to the highest power ratings, the generator will f