• The programme selector knob may be turned in either direction to select the required programme. • Always choose a programme which is suitable for the fabric type and observe the symbols on garment care labels. • With a little practice you will soon determine which programme suits your requirements. Anti Crease • The laundry may be removed after a drying cycle has been completed. • Alternatively, the laundry may be left in the drum, in which case the machine will automatically perform an Anti C

F. ELECTRICAL INFORMATION 1. Electrical Requirements It is your responsibility to have ALL electrical connections made by a properly licensed and competent electrician to ensure that the electrical installation is adequate and conforms to local and state regulations or codes. In the absence of such codes, ALL electrical connections, material, and workmanship must conform to the applicable requirements of the National Electrical Code ANSI/NFPA NO. 70-LATEST EDITION or in Canada, the Canadian Inst

as of November 11, 1998 ..........................................................4 AD-15 High Security Control Door Assembly For ALL Coin Models For OPL Models Mfd. prior to July 19, 1999 ................................................................................... AD-25 High Security Control Door Assembly For ALL Coin Models For OPL Models Mfd. prior to November 11, 1998 .........................................................................6 Phase 5 Coin Microprocessor Control Panel A

113398-12 American Dryer Corporation 88 Currant Road Fall River MA 02720-4781 USA Telephone: +1 (508) 678-9000 / Fax: +1 (508) 678-9447 e-mail: techsupport@amdry.com WARNING: For your safety the information in this manual must be followed to minimize the risk of fire or explosion and to prevent property damage, personal injury or death. — Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. — WHAT TO DO IF YOU SMELL GAS: Do not try t

(Refer to Taper Lock Bushing and Drive Motor Pulley Replacement on the previous page.) 9) Remove the taper lock bushings from the drive wheels. 10) Slide the pillow block bearings and taper lock bushing inward towards the gear (speed) reducer on the drive shaft. 11) Lift the end of the drive shaft closest to the rear of the dryer and pivot the other end of the shaft on the drive wheel until the shaft can be removed from the dryer. 12) To install new drive shaft, reverse Step #11 thru Step #2. 13

If this product is properly maintained, it will provide many years of safe, efficient, and trouble free operation. ONLY qualified technicians should service this equipment. OBSERVE ALL SAFETY PRECAUTIONS displayed on the equipment or specified in the installation manual included with the dryer. The following “FOR YOUR SAFETY” caution must be posted near the dryer in a prominent location. FOR YOUR SAFETY POUR VOTRE SECURITE Do not store or use gasoline or Ne pas entreposer ni utiliser d’essence o

as of July 24, 1999 For AD-25 OPL Models Mfd. as of November 11, 1998 Illus. No. Part No. Qty. Description 1 800150 1 Knob Latch Kit Assembly (includes illus. nos. 1 and 2) 160003 1 Dummy Lock ONLY 160104 1 MK-100 Key ONLY 2 160008 1 Lock Cam 160009 1 Knob Latch Adjustable Cam ONLY 150425 1 #12-24 x 3/8” Round Head Machine Screw ONLY (screw for knob latch adjustable cam) 3 157000 1 Drop Lint Door Spring 4 883143* 1 AD-15 Insulated Lint Door Assembly (includes illus. nos. 4 and 5) 882264* 1 AD-25

nos. 5 through 12) 7 150617 2 3/8-16 x 1” Hex Head Machine Bolt 8 153005 2 3/8” Lock Washer 9 153004 2 3/8” Flat Washer 10 801009 1 Idler Square Washer 11 152004 1 5/16-18 Hex Nut 12 150509 1 5/16-18 x 3” Hex Head Machine Bolts 36 American Dryer Corporation 450343-4 450343-4 37 Gas Burner Assembly For Models Mfd. as of May 20, 2000 Illus. No. Part No. Qty. Description 1 141104 2 Small Tube Burner 2 151001 2 #8-32 Pal Nut 3 150108 2 #8-32 x 1/2” Phillips Pan Head Machine Screw 4 140820* 2 #29 Bur

This device enables the supply voltage to reach the blower (squirrel cage fan) motor. The blower motor contactor is controlled by the Phase 5 microprocessor controller (computer). (Refer to Section b-1 on page 86 for microprocessor [computer] information.) When 24 VAC is applied to coil A1-A2, the contactor closes and enables the circuit. The blower (squirrel cage fan) motor used for gas model dryers is 15 HP (horsepower) and for steam model dryers is 25 HP (horsepower). The motor wiring configu