Das Sägeblatt dreht im Gegenuhrzeigersinn. Es wird deshalb empfohlen, NIEMALS die rechte Seite des Sägeblatts zu verwenden. Die zu verwendende Seite ist durch den graugetönten Bereich gekennzeichnet. Für wirksamen Einsatz sollte das Schneiden mittels einer schnellen Schwingbewegung gegen das abzutrennende Aststück erfolgen. Nicht allmählich schrittweise vorrücken, da sonst die Motordrehzahl sinken und der Motor abgewürgt werden kann. A WARNUNG: Die Höhe der zu schneidenden Objekte und die Ste

Alter opening the top, cut all four corners and lay the sides flat on the floor or working space. Take out all unassembled parts, bag of parts, and protective packing. 8e careful not to kink the control cables. DEFINITION OF DIRECTIONS As used throughout this manual, the following definitions apply; "Right” and '’Left” refer to the operator’s right and left when standing behind the machine in the normal operating position. "Forward” and "Rearward” likewise refer to directions from the viewpoin

Operate the machine in an open area to get the “feel” of the machine and its controls. Starting and Stopping the Engine Before starting the engine check that all bolts are tight, and that the tiller is assembled properly. Review Safety suggestions and Operating Instructions for safe and proper use of the tiller. Pre Start 1. Check the spark plug for proper connection on the spark plug. 2. Fill the fuel tank with clean, fresh, regular gasoline from an approved container. 3. Check the oil for prop

52¿ Сф1^А(Й CONTENTS Page INTRODUCTION AND DESCRIPTION..................................................................................................................................................................................................2 SAFETY • General Tiller Safety.......................................................................................................................................................................................................................

Always wear sturdy shoes and avoid wearing bulky or loose clothing while operating equipment. Never operate equipment when tired or while under the influence of drugs or alcohol. In case of emergency, know how to stop the equipment and thoroughly understand the. operation of ALL controls. Never permit anyone to operate equipment without proper instructions. Children'should not be permitted to operate the tractor or rotary tiller. KEEP CHILDREN AND PETS AT A SAFE DISTANCE DURING OPERATION. The tr

Spring 625 461469 1 Depth Bar Adjust. Pin 705 359321 1 Idler Pulley 338009 1 Idler Pulley 706 162069 1 Idler Shaft 708 359325 1 Idler Shaft Arm 709 400290 1 Capscrew NC, 3/8” x 1 3/4” 802 359330 2 Wheel Shoulder Bolt 804 400184 2 Cap Screw, NC 5/16” x 3/4” 805 400186 1 Cap Screw, NC 5/16” x 1” 400190 Cap Screw, NC 5/16” x 1 1/4” 806 400197 1 Cap Screw, NC 5/16” x 2 1/4” 807 400200 4 Cap Screw, NC 5/16” x 2 1/2” 809 400207 2 Cap Screw, NC 5/16” x 3 3/4” 811 400275 1 Cap Screw, NC 3/8” x 3” 813 40

The left brace bolts between the belt guard bracket and the transmission. The braces are mounted to the handle bars using one 1/4” - 20 x 1 1/2 and one 1/4” - 20 x 1 3/4” hex bolts, nuts, and lock washers. The clutch cable guide mounts on the outside of the right handle bar. Route the clutch cable through guide with the adjustment at the top. See Figure 1. 6. Install the handle bar cross brace between the handle bars using four 1/4” - 20 x 1 1/2” hex bolts, nuts, and lock washers. See Figure 1.

Proper clutch adjustment is very important. Minor adjustments, if needed, can be made by using the links on the clutch cable chain only. However, the friction type clutch may need further adjustment as the “V” belt stretches. Adjust as follows: 1. Remove belt guard. 2. Loosen 4 engine mount bolts. Slide engine forward or backwards as required. 3. Unhook clutch cable from load spring. 4. Push upward on idler pulley to take all slack from the drive belt. Distance between the inside of belt at the

Allow the engine to cool before storing in any enclosure. BELT COVER, BELTS, AND PULLEY REF PART # QUAN DESCRIPTION 701 271686 1 Crankshaft Pulley, 5 hp 703 162035 1 Belt Bracket Assembly ( TP, RMT) 162067 Belt Bracket Assembly (RMT55H) 703-A 359215 Belt Bracket Assembly (MT) 704 272201 1 Belt, V Drive for Units with 9” Pulley 272213 1 Belt, V Drive for Units with 7” Pulley 712 336671 1 Pulley, 9” for TP and MT 336665 1 Pulley, 7” for RMT 714 463017 1 Key, 3/16” x 3/4” Woodruff #9 715 130733 1 G

15). FIG. 15 ADJUST WHEELS FOR CULTIVATING (See Figs. 16 and 17) • Place blocks under right hand side of tiller and remove hairpin clip and clevis pin from right hand wheel. • Move wheel outward approximately 1 inch (2.5 cm) until hole in inner wheel hub lines up with inner hole in axle. • Replace clevis pin and hairpin clip on inside of wheel and remove blocks. • Repeat preceding steps on left hand side. NOTE: In extremely rough conditions and while cultivating, the wheels should be moved outwa