• Safety • Assembly • Operation • Maintenance • Parts Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A. FORM NO. 40375 (REV. 2/28/07) PRINTED IN U.S.A. TABLE OF CONTENTS SAFETY RULES...............................................................2 FULL SIZE HARDWARE CHART.....................................3 CARTON CONTENTS......................................................4 ASSEMBLY.......................................................................4 OPERATION......................

inches. 1 inch= 25.4 mm 43 TILLER --MODEL NUMBER 917.293320 MAINFRAME, RIGHT SIDE 15 13 12 4\ y 11 lO KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. DESCRIPTION 1 166532 Bumper 12 126875X Rivet, Drilled 2 73970500 Locknut,Hex, Range 5/16-18 13 102190X "Rra 3 STD551031 *Washer 11/32 x 11116x 16 Ga. 124258X Rim 4 74760512 Bolt, Hex 5/16-18x3/4 795R "RraValve 5 102332X Bracl_et,Reinforcement 14 STD541431 *Nut, Keps 5/16-18 6 7 8 74760532 102173X STD551137 Bolt'Hex 5/16-18x2 CounterWeight, R.H. *Wash

These accessories were available when the tiller was purchased. They are also available at most Sears Retail outlets and Service Centers. Most Sears Stores can order repair parts for you when you provide the model number of your tiller. ENGINE SPARK PLUG MUFFLER AIR FILTER GAS CAN ENGINE OIL STABILIZER TILLER MAINTENANCE BELT TINES SHEAR PIN HAIRPIN CLIP , 4 Your new tiller has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and

Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A. FORM NO. 48070 (REV. 5/20/08) PRINTED IN U.S.A. 2 TABLE OF CONTENTS SAFETY RULES...........................................................3 FULL SIZE HARDWARE CHART.................................4 CARTON CONTENTS..................................................5 ASSEMBLY...................................................................5 OPERATION...............................................................12 MAINTENANCE.............

PRINTED IN U.S.A. STORAGE ................................................................. 5 CARTON CONTENTS .............................................. 3 SAFETY RULES ....................................................... 2 REPAIR PARTSILLUSTRATION ........................... 7 ASSEMBLY ............................................................... 3 REPAIR PARTS LIST ............................................... 7 OPERATION .............................................................

27 TO ADJUST CARBURETOR (See Fig. 28) The carburetor has a high speed jet and has been preset at the factory and adjustment should not be necessary. However, minor adjustments may be required to compensate for differences in fuel, temperature, altitude or load_ If the carburetor does need adjustment, proceed as follows. In general, turning the idle needle valve in (clockwise) decreases the supply of fuel to the engine giving a leaner fuel!air mixture. Turning the needle valve out (counterclockwi

BELT REMOVAL • Remove reverse idler pulley from idler arnl. • Remove reverse (outside) V-belt. Remove forward (inside) V-belt from transmission pulley first and then from engine pulley. BELT REPLACEMENT • Install new forward (inside) V-belt to engine pulley first then to transmission pulley. Be sure belt is positioned on inside 9roove of both pulleys, inside all belt guides and rests on idler pulley. • Before installing reverse (outside) V-belt, turn belt =inside out". Twist so wide, flat surfac

9 • Start engine, tip tines off ground by pressing handles down and engage tine control to start tine rotation. Allow tines to rotate for five minutes. • Check tine operation and adjust if necessary. See "FINE OPERATION CHECK" in the Service and Adjustments section of this manual. TILLING HINTS _CAUTION: Until you are accustomed to handling yourtilier, start actual field use with throttle in slow position (mid-way be tween "FAST" and "iDLE"). To help tiller move forward, lift up the handles slig

• Operation • Repair Parts FailureToDo SoCanResuit in Serious Injury. sears,RoebuckandCo., HoffmanEstates,IL 60179 U,S.A. For one year from the date of purchase, when this Craf_man Gas-Powered Brushwaeker is maintained, lubricated, and tuned up accordingto the operating and maintenance instructions in the operator's manual, Sears will repair, free of charge, any defect in materials or workmanship. • • This warranty excludes the blade, nylon line, spark plug, and air filter, which are expendable

• Fast help by phone -phone support from a Sears technician on products requiring in-home repair, plus convenient repair scheduling. Once you purchase the Agreement, a simple phone call is all that it takes for you to schedule service. You can call anytime day or night, or schedule a service appointment online. Sears has over 12,000 professional repair specialists, who have access to over 4.5 million quality parts and accessories. That's the kind of professionalism you can count on to help prolo