WARNING: Proper shoulder strap and handlebar adjustments must be made with the engine completely stopped before using unit. The shoulder strap clamp must be installed as shown above the handlebar on the upper shaft (powerhead end of unit). NOTE: The lower shoulder strap clamp has two spacer tabs attached. These tabs are provided to adapt this attachment for use with powerheads that have a 1. (2.5 cm) diameter upper shaft (the shoulder strap clamp will not tighten down securely on the 1. (2.5 cm)

CHECK FOR DAMAGED OR WORN PARTS Contact an authorized service dealer for replacement of damaged or worn parts. S Blade Shield - --Discontinue use of brushcut ter attachment if shield is damaged. CHECK FOR LOOSE FASTENERS AND PARTS S Blade nut S Fasteners INSPECT AND CLEAN UNIT AND DECALS S After each use, inspect complete unit for loose or damaged parts. Clean the unit and decals using a damp cloth with a mild detergent. S Wipe off unit with a clean dry cloth. BLADE MAINTENANCE WARNING: The blad

shaft S Handlebar mounting bracket for 7/8. shaft S Bracket cover (2) S Shoulder strap S Upper shoulder strap clamp S Lower shoulder strap clamp (with spacer tabs) S Handlebar bracket screws (4) S Shoulder strap clamp screws (2) S 4- --point weed blade (assembled on brush- cutter attachment) S Large nut for installing blade S Retaining washer S Cupped washer S Metal shield (assembled on brushcutter at tachment) S Trimmer head S Plastic shield S Wing nut (screwed onto plastic shield) S Attachment

UT34020 Your new pole pruner has been engineered and manufactured to Homelite’s high standard for dependability, ease of operation, and operator safety. Properly cared for, it will give you years of rugged, trouble-free performance. WARNING: To reduce the risk of injur y, the user must read and understand the operator’s manual before using this product. Pay close attention to the Rules for Safe Operation, Warnings, and Cautions. If you use your pole pruner properly and only for what it is intend

Failure to do so can result in serious injury. PELIGRO: Lea el manual de instrucciones y siga todas las advertencias e instrucciones de seguridad. El no hacerlo puede resultar en lesiones graves. DANGER: Lire le manuel d’instructions et bien respecter tous les avertissements et toutes les instructions de securite. Tout defaut de le faire pourrait entrainer des blessures graves. Electrolux Home Products North America Div. of WCI Outdoor Products, Inc. Augusta, GA 30907 Copyright E2001 WCI Outdoor

To stop the engine, push and release the engine ON/STOP switch. PRIMER BULB The PRIMER BULB removes air from the carburetor and fuel lines and fills them with fuel. This allows you to start the engine with fewer pulls on the starter rope. Activate the primer bulb by pressing it and allowing it to return to its original form. BEFORE STARTING ENGINE WARNING: Be sure to read the fuel information in the safety rules before you begin. If you do not understand the safety rules, do not attempt to fuel

Veuilleznepasretournerleproduitaudetaillant. 1--800--554--6723RPleasedonotreturnproducttoretailer. Porfavor,nodevuelvaelproductoallugardecompra. Veuilleznepasretournerleproduitaudetaillant. 1--800--554--6723R Register your product online at: Registre su producto en linea en: Enregistrez votre produit en ligne a l’adresse : Instruction Manual Manual de Instrucciones Manuel d’Instructions PP325 For Occasional Use Only DANGER: Read and follow all Safety Rules and Operating Instructions before using

3. Fasten the strap hook to the clamp located between the throttle trigger and the handlebar mounting bracket and lift the tool to the operating position. 4. Try on shoulder strap and adjust for fit and balance before starting the engine or beginning a cutting operation. NOTE: It may be necessary to relocate the shoulder strap clamp on the shaft for proper balancing of unit. TO RELOCATE SHOULDER STRAP CLAMP: 1. Loosen and remove both clamp screws. 2. Place the upper shoulder strap clamp over the

Veuilleznepasretournerleproduitaudetaillant. 1--800--554--6723RPleasedonotreturnproducttoretailer. Porfavor,nodevuelvaelproductoallugardecompra. Veuilleznepasretournerleproduitaudetaillant. 1--800--554--6723 Register your product online at: Registre su producto en linea en: Enregistrez votre produit en ligne a l’adresse : Instruction Manual Manual de Instrucciones Manuel d’Instructions PP333 For Occasional Use Only WARNING: Read and follow all Safety Rules and Operating Instructions before using

S WHAT CAUSES BLADE THRUST --Blade Thrust can occur when spinning blade contacts an object that it does not cut. This contact causes blade to stop for an instant and then suddenly move or “thrust” away from object that was hit. The “thrusting” reaction can be violent enough to cause operator to be propelled in any direction and lose control of unit. The uncontrolled unit can cause serious injury if blade contacts operator or others. S WHEN BLADE THRUST OCCURS - -Blade Thrust can occur without wa