Войти:
Оценок - 3, средний балл: 4.3 ( )

Инструкция по эксплуатации Homelite, модель 530164830

Производитель: Homelite
Размер: 141.89 kb
Название файла: NOUS2004_530164830.pdf
Язык инструкции:en
Перейти к скачиванию



Фрагмент инструкции


CHECK FOR DAMAGED OR WORN PARTS Contact an authorized service dealer for replacement of damaged or worn parts. S Blade Shield - --Discontinue use of brushcut ter attachment if shield is damaged. CHECK FOR LOOSE FASTENERS AND PARTS S Blade nut S Fasteners INSPECT AND CLEAN UNIT AND DECALS S After each use, inspect complete unit for loose or damaged parts. Clean the unit and decals using a damp cloth with a mild detergent. S Wipe off unit with a clean dry cloth. BLADE MAINTENANCE WARNING: The blade will continue to spin after the engine stops or after the throttle trigger has been released. To avoid serious injury, make sure the blade has stopped coasting and disconnect the spark plug before performing work on the blade. WARNING: Always replace a blade that is bent, warped, cracked, broken, or damaged in any other way. Never attempt to straighten and reuse a damaged blade. Use only specified replacement blade. Wear protective gloves when handling or performing maintenance on the blade to help avoid injury. S Check blade for flatness periodically. Lay the blade on a flat surface to inspect for flatness. Throw away a blade that is not flat. SERVICEANDADJUSTMENTS BLADE REPLACEMENT 4. Remove both washers and the blade from the blade shaft. Leave the dust cup WARNING: The blade will continue to on the gearbox. spin after the engine stops or after the throttle 5. Install new blade and retaining washer onto the threaded shaft extending from the gear- trigger has been released. To avoid serious injury, make sure the blade has stopped box (blade must be between the dust cup and the retaining washer). Make sure the coasting and disconnect the spark plug before performing work on the blade. raised part of the retaining washer is facing the gearbox, and the raised area fits into the WARNING: Wear protective gloves when handling or performing maintenance on the blade to avoid injury. The blade is sharp and can cut you even when it is not moving. 1. To remove the blade, align hole in the dust cup with the hole in the side of the gearbox by rotating the blade. 2. Insert a small screwdriver into aligned holes. This will keep the shaft from turning while loosening the blade nut. Screwdriver 3. While holding the screwdriver in position, remove blade nut by turning clockwise as you are facing the nut. hole in the center of the blade. Gearbox Shield Retaining Washer Cupped Washer Nut BladeDustCupThreadedShaft 8 6. Place the cupped washer onto the shaft. 8. Tighten blade nut firmly with a wrench Make sure the cupped side of the washer while holding screwdriver in position. is toward the blade. 9. Remove the screwdriver. 7. Install blade nut by threading onto the 10. Turn blade by hand. If the blade binds shaft counterclockwise as you are facing against the shield, or appears to be unthe nut. even, the blade is not centered, and you NOTE: Make sure all parts are in place as illus-must reinstall. trated, and the blade is sandwiched between the dust cup and the retaining washer. There should be no space between the blade and the dust cup or the retaining washer. STORAGE WARNING: Perform the following steps after each use: S Allow attachment and gearbox to cool before storing or transporting. S Store attachment with blade shield in place. Position attachment so that any sharp object cannot accidentally cause injury. S Store the attachment in a dry, well ventilated area out of the reach of children. SEASONAL STORAGE Prepare attachment for storage at end of season or if it will not be used for 30 days or more. If your brushcutter attachment is to be stored for a period of time: S Clean the entire attachment. S Inspect the blade shield area and clean any dirt, grass, leaves, or debris that has collected. Inspect the blade and blade shield; replace a blade that is bent, warped, cracked, broken or damaged in any other way. S Lightly oil external metal surfaces. S Apply a coating of oil to the entire surface of the blade; wrap it in heavy paper or cloth. S Check entire attachment for loose screws or nuts. Replace any damaged, worn or broken parts. S At the beginning of the next season, use only fresh fuel having the proper gasoline to oil ratio. LIMITEDWARRANTY ELECTROLUX HOME PRODUCTS, INC., warrants to the original purchaser that each new Poulan PRO® brand gasoline tool or attachment is free from defects in material and workmanship and agrees to repair or replace under this warranty any defective gasoline product or attachment as follows from the original date of purchase. 2 YEARS - --Parts and Labor, when used for household purposes. 90 DAYS - --Parts and Labor, when used for commercial, professional, or income producing purposes. 30 DAYS - --Parts and Labor, if used for rental purposes. This warranty is not transferable and does not cover damage or liability caused by improper handling, improper maintenance, or the use of accessories and/or attachments not specifically recommended by ELECTROLUX HOME PRODUCTS, INC., for this tool. Addit...

Эта инструкция также подходит к моделям:
Садовые инструменты - 530164830 (141.89 kb)

Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории