Оценок - 1, средний балл: 4 ( )

Производитель: Homelite Размер: 330.78 kb Название файла: Язык инструкции:

3. Fasten the strap hook to the clamp located between the throttle trigger and the handlebar mounting bracket and lift the tool to the operating position. 4. Try on shoulder strap and adjust for fit and balance before starting the engine or beginning a cutting operation. NOTE: It may be necessary to relocate the shoulder strap clamp on the shaft for proper balancing of unit. TO RELOCATE SHOULDER STRAP CLAMP: 1. Loosen and remove both clamp screws. 2. Place the upper shoulder strap clamp over the shaft. 3. Position the lower shoulder strap clamp under the shaft and align the upper and lower clamp screw holes. UpperShoulderStrapClamp Screws Lower Shoulder Strap Clamp 4. Insert two screws into the screw holes. 5. Secure shoulder strap clamp by tightening screws with a hex wrench. SHOULDERSTRAPADJUSTMENTFORBALANCE6inches(15cm) belowwaist30inches(76cm) minimum4--12inches(10--30cm) aboveground 30inches(76cm) minimum CONFIGURING YOUR UNIT You can configure your unit using a cutting head for grass and light weeds, or a weed blade for cutting grass, weeds, and brush up to 1/2 inch (1 cm) in diameter. To assemble your unit, go to the section for the desired configuration and follow the instructions. 7 ASSEMBLY INFORMATION - -TRIMMER HEAD TRIMMER HEAD NOTE: Remove the blade and metal shield before attaching the plastic shield and trimmer head. To remove blade, align hole in the dust cup with the hole in the side of the gearbox by rotating the blade. Insert a small screwdriver into aligned holes. This will keep the shaft from turning while loosening the blade nut. Remove blade nut by turning clockwise. Remove the screwdriver. Remove both washers and blade. To remove metal shield, loosen and remove the four mounting screws. See ATTACHING THE METAL SHIELD and INSTALLATION OF THE METAL BLADE for illustrations. Be sure to store all parts and instructions for future use. ATTACHING THE PLASTIC SHIELD ANDTRIMMERHEAD WARNING: The shield must be properly installed. The shield provides partial protection to the operator and others from the risk of thrown objects, and is equipped with a line limiter blade which cuts excess line to the proper length. The line limiter blade (on underside of shield) is sharp and can cut you. 1. Remove wing nut from shield. 2. Insert bracket into slot on shield. 3. Pivot shield until bolt passes through hole in bracket. BracketSlotShield 4. Reinstall wing nut and tighten securely. WingNut NOTE:Ifyourunithasaplasticcoveroverthethreadsonthethreadedshaft,removethecoveringtoexposethethreads.Beforeinstallingthetrimmerhead, makesurethedustcupandretainingwasherarepositionedonthegearboxasshownbelow. RetainingWasherDustCupGearboxAlignedHoles NOTE: Make sure all parts are properly installed as shown in the illustration before installing the trimmer head. 5. Align hole in the dust cup with the hole in the side of the gearbox by rotating the dust cup. 6. Insert a small screwdriver into aligned holes. This will keep the shaft from turning while tightening trimmer head. 7. While holding the screwdriver in position, thread trimmer head onto the shaft in the direction shown on the decal (counterclockwise looking from bottom of unit). Tighten until secure. NOTE: The retaining washer must be positioned with the raised section facing toward the gearbox. ASSEMBLY INFORMATION - --WEED BLADE WEED BLADE NOTE: Remove the trimmer head and plastic shield before attaching the metal shield and installing the weed blade. To remove the trimmer head, align hole in the dust cup with the hole 8 in the side of the gearbox by rotating the dust cup. Insert a small screwdriver into aligned holes. This will keep the shaft from turning while loosening the trimmer head. Remove the trimmer head by turning clockwise. Remove the screwdriver. To remove the plastic shield, loosen and remove wing nut. Pivot shield to release bracket from slot. See INSTALLATION OF THE CUTTING HEAD and ATTACHING THE PLASTIC SHIELD for illustrations. Be sure to store all parts and instructions for future use. Never use the trimmer head with the metal blade installed. ATTACHING THE METAL SHIELD WARNING: The metal shield must be properly installed on the tool anytime the tool is used with a blade. The forward tip of the metal shield helps to reduce the occurrence of blade thrust which can cause serious injury such as amputation to the operator or bystanders. Failure to install the shield in the position shown can result in serious injury to the operator. The length of the shield must be aligned with the length of the shaft. ShaftMetalShieldBlade 1. Place the metal shield under the gearbox, and align the screw holes. ShieldGearbox 2. Insert and thread the 4 mounting screws through the holes of the gearbox and the metal shield. Tighten evenly and securely with the hex wrench provided. INSTALLATION OF THE METAL BLADE WARNING: Wear protective gloves when handling or performing maintenance on the blade to avoid injury. The blade is sharp and can cut you even when it is no...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: