Оценок - 4, средний балл: 3.8 ( )

Производитель: Campbell Hausfeld Размер: 6.56 mb Название файла: Язык инструкции:

Paint requires thinning B. Follow paint manufacturers thinning recommendations. Paint should not typically need to be thinned more than 8 oz. of solvent per gallon C. Reversible Spray Tip in cleaning position C. Turn Spray Tip to Spray position. See Cleaning section for details Pump primes and builds pressure, but does not maintain pressure once trigger is pulled 24.Clogged Suction Filter 25.Suction Assembly loose and/or sealing surfaces are dirty at Inlet Valve 24.Remove Suction Filter and clean. Also, refer to Maintenance section 25.Remove Suction Assembly, clean sealing surfaces and reassemble hand tight 26.Paint thick due to cold weather. This problem usually occurs with Latex based coatings 26.Do not paint Latex coatings in temperatures less than 50°F (10°C). Refer to paint manufactures minimum painting temperature recommendations 27.Inlet Valve and/or Outlet Valve 27.Replace valves. Also, refer to Maintenance section are worn Gun will not shut-off 28.Trash caught in Gun Valve 28.Clean or replace Gun valve. Also, refer to Gun Maintenance section. This is a very rare occurrence, and will not occur if filters are properly maintained 29.Worn Gun Valve 29.Replace Gun valve. Also, refer to Gun Maintenance section 30.Dried paint under gun actuator 30.Remove 1/4” nut and gun actuator at rear of gun. Remove dried paint from around needle and back of actuator. Replace actuator and 1/4” nut. Set gun trigger position with trigger lock in locked orientation (tabs horizontal) by the following instructions: With one hand holding trigger softly against lock, use a 1/4” nut driver to turn nut in until trigger starts to come off the lock, then back off the nut (counterclockwise) 1/2 turn. Pulling the trigger must not open the gun valve when trigger lock is activated. You should be able to get the actuator to wiggle slightly with your finger while holding the trigger against the locked trigger lock. After moving equipment or adding paint to bucket, unit will not prime or spray 31.Suction assembly loose or damaged 31.Tighten suction assembly onto inlet valve. Re-prime sprayer. If problem is not remedied, consult Technical Support Oil in Paint 32.Oil is leaking from between Block and Hydraulic Housing 32.Check hydraulic oil level. Add hydraulic oil if necessary (it is recommended that this be done by a qualified technician). Check block bolt torque 33.Diaphragm is damaged 33.New diaphragm assembly is needed. (It is recommended that this be done by a qualified technician.) Refer to Maintenance Chart concerning torque settings and type of tools required to reassemble block onto housing. Refill piston with hydraulic oil. Correct assembly of internal check valve under diaphragm assembly is critical to proper operation of the pump – refer to Parts List or contact technical Support Fluid leaks other than oil 34.Loose connection 34.Clean sealing surface and reassemble per assembly instructions 35.Contaminated sealing surface 35.Consult technical support 36.Damaged component 36.Consult technical support Symptoms not listed 37.Possible product quality issue. (We would greatly appreciate your assistance in continuous product quality improvement) 37.Call technical support at 1-800-626-4401 22 Airless Paint Sprayers To remove trash that has been caught in the valves, the unit can be force fed. With pump on and prime/spray knob turned to “prime” position, pour the appropriate solvent into the suction tube and then fold hose as shown opposite. While firmly squeezing the suction tube, slide hand down toward the pump and repeat until pump primes. “Force Feeding” Pump Notes: • Weather conditions can cause unsatisfactory results when spraying some coatings. • High humidity prolongs set, and cure times. • High temperatures decrease set, and cure times. • C old temperatures extend set, and cure times. • Variations in temperature, and humidity can cause variations in finish quality. • C oating manufacturers can recommend additives to resolve some of these problems, and should be contacted for assistance with particular problem resolutions. 23 Operating Instructions and Assembly Instructions Operating Instructions and Assembly Instructions Airless Paint Sprayers Limited Warranty 1. DURATION: From the date of purchase by the original purchaser as follows: Paint Application Systems -5 years. All Paint Spray Guns and Paint Application Accessories -1 year. 2. WHO GIVES THIS WARRANTY (WARRANTOR): campbell Hausfeld/A Scott Fetzer company, 100 Production drive, Harrison, Ohio, 45030, Telephone: 1-800-626-4401. 3. WHO RECEIVES THIS WARRANTY (PURCHASER): The original purchaser (other than for purposes of resale or rental) of the campbell Hausfeld Product. 4. WHAT PRODUCTS ARE COVERED BY THIS WARRANTY: PS270d or PS271d Airless Painting System. 5. WHAT IS COVERED UNDER THIS WARRANTY: defects in material and workmanship which occur within the duration of the warranty period. Warrantor will also cover normal wear items for a...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: