PROGRAMMING TRANSMITTERS: NOTE: It is important to remember that during the programming mode, each individual step must be completed within 15 seconds ofthe previous step. If the 15 second time limit expires betweensteps, the unit will automatically exit the program mode. Thisis indicated by a long chirp from the siren. Non alarm models will flash the parking lights only to confirm thetransmitter code has been learned and stored. NOTE: Because the system may be capable of sounding a siren, the v

This transmitter can be used with any Audiovox unit color coded with an Orange LED in the receiver. To program this transmitter into your remote start upgrade unit: 1) Turn the ignition to the on position. 2) Press and release the programming switch 3 times. 3) Press and hold, for 3 seconds, the button of the transmitter you wish to add until the parking light flashes indicating the transmitter has been learned. 4) Repeat step 3 for each transmitter up to a total of 4. Turn the ignition of

Although this transmitter can be programmed into any of the Audiovox remote start and/or alarm, remote start systems, it will offer limited use and should be used for the remote start upgrade only. To program this transmitter into your remote start upgrade unit: 1) Turn the ignition to the on position. 2) Press and release the programming switch 3 times. 3) Press and hold, for 3 seconds, the button of the transmitter you wish to add until the parking light flashes, indicating the transmitter

Lock and arm/unlock and disarm. May be programmed to unlock driver's door or all doors. Also will initiate and terminate *Panic. Pulsed or switched output to control Remote Trunk Release or optional device connected to channel 3. When pressed and release two times, will provide pulsed output or activate the Remote Start option when installed. When so equipped, this button can be used to operate an optional device connected to channel 4. When so equipped, this button can be used to operate an opt

Although this transmitter can be programmed into any of the Audiovox remote start and or alarm, remote start systems, it will offer limited use and should be used for the remote start upgrade only. To program this transmitter into your remote start upgrade unit: 1) Turn the ignition to the on position 2) Press and release the programming switch 3 times 3) Press and hold, for 3 seconds, the button of the transmitter you wish to add until the parking light flashes indicating the transmitter ha

This allows you to program eachtransmitter to more than one vehicle in two car families and also allows youto change which button or buttons control certain functions of the system. (Example: Transmitter channel 5, shown below, can be programmed toactivate Receiver channel 2.) Refer to the chart below for access to each ofthe transmitter channels, and for the standard factory button assignments. TRANSMITTER SYSTEM RECEIVER CHANNEL BUTTONS CHANNEL FUNCTION 1 1 Remote Arm * Remote Emergency Panic*

2) Remove the rear cover to access the discharged battery payingattention to the proper polarity orientation. 3) Carefully remove and properly dispose of the discharged battery. 4) Insert the new battery, close the case, then reinstall the small casescrew removed in step 1.5) If you accidently dislodge the cir- cuit board from the transmitter hous- ing, be certain that the rubber mem- brane is seated properly, and thebuttons are properly exposed fromthe front view of the case, theninsert the cir

These icons are programmed at time of installation to meet the needs of the individual and to complement the vehicle that the system is installed in. To replace a transmitter or add transmitters, please follow the programming instructions listed on the pages of this manual. Transmitter Programming Guide Model AX-2K4 AX-2K4S, AX-2K4MS, & AX-2K4MSFL * Where So Equipped 128-6987 1 of 6 Some of the more popular options available for the unused Option Buttons of your transmitter are: AS 9554 Remote G

These will be used during the program processto identify transmitters that will continue to be used. Enter the transmitter program mode: 1. Turn the ignition switch to the “ON” position. 2. Within 10 seconds, press and release the valet/program switchthree times. (Siren emits 1 short chirp indicating channel 1 hasbeen entered) 3. Within 10 Seconds, press and hold the ARM or ARM/DISARM 3 128-6987 3 of 6 button of the first transmitter you wish to remain stored into the control unit until a single

"Repeat step 8 for each transmitter you wish to program". 9) Press and release the valet push button switch one time to advanceto channel 4 if so equipped. The siren will chirp 4 times and thedash mounted LED will Flash 4 times, indicating that the unit is readyto accept programming for channel # 4, optional device (whereequipped) 10) Press and hold the Option button of the transmitter you wish toprogram for 4 seconds or until a long chirp is heard from the siren. "Repeat step 10 for each transm