Оценок - 4, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
These will be used during the program processto identify transmitters that will continue to be used. Enter the transmitter program mode: 1. Turn the ignition switch to the “ON” position. 2. Within 10 seconds, press and release the valet/program switchthree times. (Siren emits 1 short chirp indicating channel 1 hasbeen entered) 3. Within 10 Seconds, press and hold the ARM or ARM/DISARM 3 128-6987 3 of 6 button of the first transmitter you wish to remain stored into the control unit until a single chirp is heard from the siren. (Repeat this for each transmitter you wish to remain stored in the controlunit). The receiver stores up to four transmitters. To be certain all transmitter slots in the receiver are occupied with transmitters you wish to continue to use, and all others are erased, you will have to fill all fourreceiver slots. If in step 3 you identified one transmitter, you will haveto fill the additional 3 slots. If in step 3 you identified two transmitters, you will have to fill the additional two slots, etc... 4. Press and hold any unused button or combination of buttons until along chirp is heard from the siren. Release and press the button orbutton combination again and again until all remaining slots are full. NOTE: The button or combination of buttons entered will also control the arm or arm/disarm function until additional transmitters areadded. All unwanted transmitters are now deleted. REPRIORITIZING A TRANSMITTER’S PROGRAMMING: To reprogram a receiver channel with a different transmitter buttononce a code has been stored, there will be two options: 1. Enter the transmitter program mode of the receiver channel to bereprogrammed. Using any unused button or combination of buttons, push out the stored code by pressing the unused button untila long chirp is heard, then repeat 3 additional times. After this, youcan add any desired unused transmitter button. This action erases only the button stored of the transmitter you are programming. All other codes will remain stored. 2. Enter the transmitter program mode. Using any transmitter buttonpress and hold until a long chirp is heard. If a single chirp or multiplechirps, (up to 7 chirps), are heard, the unit is indicating that thetransmitter has already been programmed elsewhere in the receiver. Release the transmitter button and within 5 seconds pressand hold until a long chirp is heard. This action forces the unit to erase all stored codes of that transmitter. The unit then exits the program mode the siren emits the program modeexit chirp pattern. All transmitter buttons for that transmitter must now be reprogrammed. Any other transmitter stored in the unit’s memorystill remain operational. If the button is released and not pressed againwithin the 5 second period, no change in programming has been madeto the receiver channel. The programmer can move onto a differentchannel or erase the transmitter codes as described in 1 above. OPERATING THE FLASHLIGHT OF AX-2K4FL If the transmitter packaged with your system included theAX-2K4FL, (Flashlight Transmitter) By pressing the button located onthe side of the transmitter will cause the light on the end of the unit toturn on. 4 128-6987 4 of 6 BATTERY REPLACEMENT: The transmitter incorporates a small LED visible through the case whichis used to indicate battery condition. You will notice a decrease in transmitter range as the battery condition deteriorates. Transmit- ter battery replacement is recommended at least every 10 to 12 months, depending upon how frequently the transmitter is used. To replace the battery: 1) Remove the small # 0 phillips head screw from the rear of the case. 2) Remove the rear cover to access the discharged battery payingattention to the proper polarity orientation. 3) Carefully remove and properly dispose of the discharged battery. 4) Insert the new battery, close the case, then reinstall the small casescrew removed in step 1.5) If you accidently dislodge the cir- cuit board from the transmitter hous- ing, be certain that the rubber mem- brane is seated properly, and thebuttons are properly exposed fromthe front view of the case, theninsert the circuit board, and returnto step #4. QUICK REFERENCE CHART: You can program an...
Эта инструкция также подходит к моделям:Радиоприемники - AX-2K4 (101.65 kb)
Радиоприемники - AX-2K4MS (101.65 kb)
Радиоприемники - AX-2K4S (101.65 kb)