Оценок - 3, средний балл: 3.3
(
)
)
|
Фрагмент инструкции
PROGRAMMING TRANSMITTERS: NOTE: It is important to remember that during the programming mode, each individual step must be completed within 15 seconds ofthe previous step. If the 15 second time limit expires betweensteps, the unit will automatically exit the program mode. Thisis indicated by a long chirp from the siren. Non alarm models will flash the parking lights only to confirm thetransmitter code has been learned and stored. NOTE: Because the system may be capable of sounding a siren, the vehicle horn, or both, where the siren chirp is referenced below, the siren may chirp, the horn may beep, or both devicesmay sound. NOTE: Some systems are capable of single button programming, if youralarm module is capable of this feature, simply complete step 4of these programming instructions for each transmitter you wishto control your system and exit the program mode by switchingoff the ignition key. TO PROGRAM ADDITIONAL TRANSMITTERS: 1) Enter the vehicle, and turn the ignition switch to the on position. 2) Press and release the valet push button switch three times. NOTE: Some systems may use a combination pushbutton LEDswitch. In these systems the pushbutton and the dash- mounted LED are one and the same. 3) The dash mounted LED will flash 1x, and the siren will chirp 1x, indicating that the system is ready to accept programming of channel#1 which is arm/lock, disarm/unlock/unlock 2, and panic functions. 2 128-8698 2 of 8 4) Press and hold the lock or lock/unlock symbol button of the transmitter you wish to program for 4 seconds or until a long chirp is heardfrom the siren. "Repeat step 4 for each transmitter you wish to program". NOTE: If your transmitter button has the Lock/Unlock icon on onebutton, press and release the valet push button switch 2 timesthen move on to step #8.5) Press and release the valet push button switch one time to advanceto channel 2. The siren will chirp 2 times and the dash mounted LEDwill Flash 2 times, indicating that the unit is ready to accept programming for channel # 2 which is only used for separate lock andunlock button transmitters and is the disarm/unlock/unlock 2 andpanic. 6) Press and hold the unlock symbol button of the transmitter you wishto program for 4 seconds or until a long chirp is heard from thesiren. "Repeat step 6 for each transmitter you wish to program". 7) Press and release the valet push button switch one time to advance to channel 3. The siren will chirp 3 times and the dashmounted LED will Flash 3 times, indicating that the unit is readyto accept programming for channel # 3 which is the trunk release/ alternate output channel of the system. 8) Press and hold the trunk/key symbol button of the transmitter youwish to program for 4 seconds or until a long chirp is heard from thesiren. "Repeat step 8 for each transmitter you wish to program". 9) Press and release the valet push button switch one time to advanceto channel 4 if so equipped. The siren will chirp 4 times and thedash-mounted LED will Flash 4 times, indicating that the unit is readyto accept programming for channel # 4, optional device (whereequipped). 10) Press and hold the Option button of the transmitter you wish toprogram for 4 seconds or until a long chirp is heard from the siren. "Repeat step 10 for each transmitter you wish to program". 11) Press and release the valet push button switch one time to advanceto channel 5 if so equipped. The siren will chirp 5 times and thedash-mounted LED will Flash 5 times, indicating that the unit isready to accept programming for channel # 5 optional device (whereequipped). 12) Press and hold the second Option button of the transmitter you wishto program for 4 seconds or until a long chirp is heard from the siren. "Repeat step 12 for each transmitter you wish to program". 13) Within 10 seconds, press and release the valet program switchone time. (Siren emits 6 short chirps indicating channel 6 has been entered) 3 128-8698 3 of 8 14) Within 10 Seconds, press and hold the unlock button, (or anyunused button(s)), of the first transmitter you wish to controlChannel 6 output, (Driver Priority 1) until a long chirp is heardfrom the siren. (Repeat this for each transmitter you wish to operate the Channel 6 output, Driver Priority 1) 15) Within 10 seconds, press and release the valet program switchone time. (Siren emits 7 short chirps indicating channel 7 has been entered) 16) Within 10 Seconds, Press and hold the unlock button (or anyunused button(s)) of the first transmitter you wish to controlChannel 7 output, (Driver Priority 2) until a long chirp is heardfrom the siren. (Repeat this for each transmitter you wish to operate the Channel 7 output, Driver Priority 2) NOTE: Channels 6 and 7 can be used as a separate output tocontrol a function other than driver priority. Simply programming any unused transmitter button other than the unlockbutton will allow complete independent control of these outputs. ERASING TRANSMITTERS IF THEY HAVE BEEN LOST OR STOLEN: NOTE: Bef...