Check the power connections to the receiver. There must be at least 20 VAC at the receiver power connections. (If a 24V system). Review the code switch and the selector switch settings then reprogram the receiver.. Try a different code switch setting. Check the antenna installation. Wait one minute for the receiver to “warm-up”. Check battery in transmitter. RECEIVER “CLICKS” WHEN ANY TRANSMITTER BUTTON IS PUSHED, BUT NOTHING ELSE HAPPENS. Check the wire & connections in the STOP circuit. Refer

Put the transmitter in program mode. controlled devices such as a garage door opener, 2. Select the button you wish to use. with a single transmitter. 3. Enter your 9 digit code. Follow these simple instructions. Please read the instructions completely before starting. Further instructions are available at INSTRUCTIONS FOR REPLACEMENT TRANSMITTERS Select the block of switches below that best matches the one in the transmitter or receiver that you are replacing. *The grids display an EXAMPLE usin

The transmitter to attach the unit to a code is retained in permanent memory and will not be sun visor. If the clip is lost during battery replacement. To replace the used, slide it into the batteries, remove the back of the case with a small recess provided on the screwdriver. Carefully slip the batteries out of the back of the transmitter holders and replace with fresh CR2032 3- volt batteries. case until the snaps on the case fit around the clip. The “+ ” on the batteries must point away from

Defective parts will be repaired or replaced with new or factory rebuilt parts at Allstar’s sole option. This limited warranty does not cover non-defect damage, damage caused by unreasonable use, damage caused by improper installation or care, vandalism or lightning, fire or excessive heat, flood or other acts of God (including, but not limited to misuse, abuse or alterations, failure to provide reasonable and necessary maintenance) , labor charges for dismantling or reinstalling a repaired or r

The LED will blink off once and then remain on. Go to Step 3. .. - ENTER YOUR 9 DIGIT CODE 3. Enter the 9- digit code from the table pressing the buttons that correspond with the grid above. (If your block has 8 switches use the + button in the 9th position) Go to Step 4. .. 4. After the 9- digit code is entered, the LED will blink twice to confirm a valid code and remain off. 5. Repeat the procedure for the remaining buttons. INSTRUCTIONS FOR USE WITH AN ALLSTAR SMART RECEIVER When using the Al

Next, button. The Red LED will turn on. Next, while continuing to hold the + button, while continuing to hold the - button, press and hold the - button. Continue press and hold the + button. Continue to hold both buttons until the LED starts to to hold both buttons until the LED starts to blink ( approximately 5 seconds) . Release blink ( approximately 5 seconds) . Release both buttons while the LED is blinking. both buttons while the LED is blinking. The LED will blink two times and then The LE

8 switches w/ + 0 - WARNING Disconnect power to operator before any installation or repair. Follow all instructions provided by the manufacturer of your operator. After installing your receiver and transmitter, check the operation of your radio controls by moving approximately 45 feet back from the garage door, then press the transmitter button. Operation at this distance should be reliable. However, environmental conditions and the location of the transmitter and receiver will affect distance.

All implied warranties of merchantability and/ or fitness for a particular purpose are hereby disclaimed and excluded. Under no circumstances shall Allstar be liable for consequential, incidental or special damages arising in connection with the use or inability to use this product. In no event shall Allstar’s liability for breach of warranty, breach of contract, negligence or strict liability exceed the cost of the product covered hereby. No person is authorized to assume for Allstar any other

controlled devices such as a garage door opener, 2. Select the button you wish to use. with a single transmitter. 3. Enter your 9 digit code. Follow these simple instructions. Please read the instructions completely before starting. Further instructions are available at INSTRUCTIONS FOR REPLACEMENT TRANSMITTERS Select the block of switches below that best matches the one in the transmitter or receiver that you are replacing. *The grids display an EXAMPLE using the code shown on the switches to t

Start coding by exactly matching all 8 code switches in the transmitter and receiver. Next, in receiver A1, set code switch #6 to +, set code switch #7 to + and code switch #8 to +; In receiver A2, set code switch #6 to +, set code switch #7 to + and code switch #8 to 0. Continue setting the codes in the 831 receivers, using both tables shown above. TRANSMITTER A-B-C Selector Switch Position RECEIVER Coding Switch #6 A + B 0 C - TRANSMITTER 1 - 9 Selector Switch Position 831 RECEIVER Code Switch